MAX4544CSA+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 60Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4544 |
| Pin Count | 8 |
| Power Supplies | 3.3/5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Nominal Supply Current | 100pA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 100 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 75 ns |
| On-State Resistance (Max) | 60Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 76 dB |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 0.8Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 100ns, 75ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 800m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4544CSA+T Overview
Due to its 8-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. The advanced packaging method Tape & Reel (TR) provides high reliability. Mounted in Surface Mount is this multiplexer. In the multiplexer and demultiplexer, 2:1 represents the number of circuits. Temperatures around 0°C~70°C TA are extended for operation. Total terminations are 8. As a result of its 1 channels, this electronic component provides high-quality output. If the voltage supply is 5V volts, the electrical component should be turned on and run. It is part of the design of the 8 series that this electronic component is included. The analog switch ics are built using SPDT switching circuits. A 1 circuit is present in this switch device. Try searching for the analog switch ic with MAX4544 if you are looking for variants. Analog switches have 60Ohm internal resistance. For details about the functions of 8 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 12V to the switch device in normal circumstances. An effective Single supply digital multiplexer. 2.7V should be the lowest voltage fed to the electronic component. Analogue multiplexers require a 2.7V~12V voltage to drain from a single voltage supply. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer.
MAX4544CSA+T Features
1 Channels
Switch Circuit: SPDT
MAX4544CSA+T Applications
There are a lot of Maxim Integrated MAX4544CSA+T Analog Switches & Multiplexers ICs applications.
- Fault Tolerant Systems
- Fiber In The Loop (FITL)
- SONET
- Automatic test equipment
- Channelized and Unchannelized DS3 applications
- SDH/SONET multiplexers
- Microprocessor Controlled Analog Systems
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- PCMCIA cards
- PBX interfaces
