MAX4544CUA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 60Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4544 |
| Pin Count | 8 |
| Polarity | Non-Inverting |
| Power Supplies | 3.3/5V |
| Number of Channels | 2 |
| Number of Circuits | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Nominal Supply Current | 100pA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 100 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 75 ns |
| On-State Resistance (Max) | 60Ohm |
| High Level Output Current | 10mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 76 dB |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 0.8Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 100ns, 75ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 800m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
MAX4544CUA+ Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). High reliability is ensured by the advanced packaging method Tube. In Surface Mount, this analog switch is mounted. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Increasing operating temperature to around 0°C~70°C TA. There are 8 terminations totally. A 2 channel electronic part produces high-quality output. When the electronic component is given a voltage of 5V, it should be turned on and run. As part of the design of the 8 series, this electronic part has been incorporated into the system. Unlike digital switches, these are based on SPDT switching circuits. Circuits number 1 make up this analogue multiplexer. Using the MAX4544 search parameter, you can discover variants of the switch. A 60Ohm internal resistance characterizes this multiplexer. Please refer to the datasheets for 8 pins functions. The analog multiplexer shown here is a typical Multiplexer or Switches. A voltage higher than 12V should not normally be supplied to the switches. Analog switch ics with Single supply type are cost-effective. 2.7V is the lowest voltage the electrical component should receive. An analogue multiplexer drains from a single voltage supply at 2.7V~12V. A digital multiplexer may suffer damage if voltage is applied above 1μA.
MAX4544CUA+ Features
2 Channels
Switch Circuit: SPDT
MAX4544CUA+ Applications
There are a lot of Maxim Integrated MAX4544CUA+ Analog Switches & Multiplexers ICs applications.
- Audio signal routing
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Switching Systems
- MP3 players
- Digital access cross connects
- ATM
- PDAs
- Fiber to the Home
- Battery Powered Systems
- Optical Applications
