MAX4544CUA+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 60Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4544 |
| Pin Count | 8 |
| Power Supplies | 3.3/5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Nominal Supply Current | 100pA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 100 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 75 ns |
| On-State Resistance (Max) | 60Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 76 dB |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 0.8Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 100ns, 75ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 800m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4544CUA+T Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. In Surface Mount, this analog switch is mounted. Multiplexer and demultiplexer circuits have a number 2:1. Operational temperature extended around 0°C~70°C TA. 8 terminations have been made so far. The electronic part provides high-quality output because it has 1 channels. An 5V voltage supply should allow the electrical part to be turned on and run. As part of its design, the 8 series is equipped with this electronic component. Circuits based on SPDT switching are used to construct these analog switch ics. The circuits in this analogue multiplexer number 1. Try searching with MAX4544 to find analog multiplexer variants. The internal resistance of this digital multiplexer is 60Ohm. The datasheets for the 8 pins explain the functions. It is a typical Multiplexer or Switches analog multiplexer. A voltage higher than 12V should not normally be supplied to the switches. The digital multiplexer has a low cost Single supply. 2.7V should be the lowest voltage fed to the electronic component. A voltage of 2.7V~12V is required for this switch device, which drains from a single voltage source. Put voltage above 1μA on the multiplexer to cause damage.
MAX4544CUA+T Features
1 Channels
Switch Circuit: SPDT
MAX4544CUA+T Applications
There are a lot of Maxim Integrated MAX4544CUA+T Analog Switches & Multiplexers ICs applications.
- Microwave transmission systems
- SONET
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Industrial and process control systems
- PDAs
- Cross Connects
- High-Voltage
- E1 Network Equipment
- New designs requiring multiplexer functions
