MAX4544EPA
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Resistance | 60Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4544 |
| Pin Count | 8 |
| Power Supplies | 3.3/5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| On-State Resistance (Max) | 60Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 76 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 0.8Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 100ns, 75ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 800m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 75ns |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Height Seated (Max) | 4.572mm |
| Length | 9.375mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4544EPA Overview
The electrical component comes in 8-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. High reliability is achieved by using advanced packaging method Tube. A switch device like this is mounted in Through Hole. Multiplexers and demultiplexers have the same number of circuits 2:1. Operating temperature extended to -40°C~85°C TA. Totally, there are 8 terminations. The electronic part provides high-quality output because it has 1 channels. A 5V voltage supply should turn on and run the electronic component. The electronic part body is injected with 8 pins. A SPDT switching circuit is used for these analog switches. Circuits number 1 make up this analogue multiplexer. Look for analog switch ic variants by searching with MAX4544. Internally, this switch multiplexer has a resistance of 60Ohm. You can find the functions of the 8 pins in the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. Users should never supply a voltage higher than 12V to a switch device. 2.7V is the lowest voltage the electrical component should receive. Using a single voltage supply, this switch device consumes 2.7V~12V volts.
MAX4544EPA Features
1 Channels
Switch Circuit: SPDT
MAX4544EPA Applications
There are a lot of Maxim Integrated MAX4544EPA Analog Switches & Multiplexers ICs applications.
- Digital cross connects (DSX-1)
- Battery Powered Instruments
- Data switching
- Precision data acquisition
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Multi-Line E1 Interface Cards
- Cellular phones
- SONET/SDH ADM
- Avionics test equipment
- USB 1.1 signal switching circuits
