MAX4544ESA+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2001 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 60Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 727mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4544 |
| Pin Count | 8 |
| JESD-30 Code | R-PDSO-G8 |
| Power Supplies | 3.3/5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Nominal Supply Current | 100pA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 100 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 75 ns |
| On-State Resistance (Max) | 60Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 76 dB |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 0.8Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 100ns, 75ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 800m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4544ESA+T Overview
As the electronic part is packed in 8-SOIC (0.154, 3.90mm Width), international shipping is convenient. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have a ratio of 2:1. Temperatures around -40°C~85°C TA are extended for operation. Total terminations are 8. As a result of its 1 channels, this electronic component provides high-quality output. When the electronic component is given a voltage of 5V, it should be turned on and run. Into the electrical component body are injected 8 pins. On the other hand, analog switches can be constructed using SPDT switching circuits. A 1 circuit is present in this switch device. Use MAX4544 to search for variants of the digital switches. There is 60Ohm internal resistance in this digital multiplexer. This switch device is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 12V to the switch device in normal circumstances. A cost-effective Single supply type analogue multiplexer. A low voltage of 2.7V should be applied to the electronic component. A voltage of 2.7V~12V is required for this switch device, which drains from a single voltage source. If you put voltage higher than 1μA on the digital multiplexer, damage may occur.
MAX4544ESA+T Features
1 Channels
Switch Circuit: SPDT
MAX4544ESA+T Applications
There are a lot of Maxim Integrated MAX4544ESA+T Analog Switches & Multiplexers ICs applications.
- Medical systems
- E1 Network Equipment
- Signal routing between systems
- Modems
- ATM
- Cell phones
- Intelligent PBX
- Mechanical reed relay replacement
- Public switching systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
