MAX4544EUA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2003 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 60Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 330mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4544 |
| Pin Count | 8 |
| Operating Supply Voltage | 9V |
| Power Supplies | 3.3/5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2.7V |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 125 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 400 ns |
| On-State Resistance (Max) | 60Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 76 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| On-state Resistance Match-Nom | 0.8Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 100ns, 75ns |
| Charge Injection | 1pC |
| Channel-to-Channel Matching (ΔRon) | 800m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 75ns |
| Voltage - Supply, Single (V+) | 2.7V~12V |
| Height | 950μm |
| Length | 3.1mm |
| Width | 3.1mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4544EUA+ Overview
Due to its 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) packaging, the electronic part is convenient for international shipping. Advanced packaging method Tube is used to provide high reliability. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have a ratio of 2:1. Operational temperature extended around -40°C~85°C TA. A total of 8 terminations have been recorded. By its 1 channels, the electronic component provides high-quality output. A 5V voltage supply should turn on and run the electronic component. As part of its design, the 8 series is equipped with this electronic component. The analog switch ics are built using SPDT switching circuits. The circuits in this analogue multiplexer number 1. Try searching with MAX4544 if you're looking for variants. A 60Ohm internal resistance characterizes this multiplexer. Datasheets for functions of 8 pins are available. The analogue multiplexer in this example is a typical Multiplexer or Switches. A voltage higher than 12V should not normally be supplied to the switches. The analog switch ic is of the Single supply type and is cost-effective. There should be 2.7V voltage fed to the electrical part below 2.7V. The voltage required by this switch device is 2.7V~12V, draining from a single voltage supply. It may damage the digital multiplexer if the voltage is higher than 1μA. There is a voltage range of 9V operating voltages for the electrical part.
MAX4544EUA+ Features
1 Channels
Switch Circuit: SPDT
MAX4544EUA+ Applications
There are a lot of Maxim Integrated MAX4544EUA+ Analog Switches & Multiplexers ICs applications.
- Microprocessor controlled systems
- PDAs
- T1/E1 Terminals
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Fiber In The Loop (FITL)
- E1 Multiplexer
- Imaging
- Multiplexers
- Data Acquisition Systems
- Cross Connects
