MAX4551CEE+T

110ns, 90ns SPST - NC 120Ohm Analog Switches BREAK-BEFORE-MAKE MAX4551 16 Pins 1nA 5V 16-SSOP (0.154, 3.90mm Width)

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX4551CEE+T
Package: 16-SSOP (0.154, 3.90mm Width)
Datasheet: PDF
Stock: 402
Description: 110ns, 90ns SPST - NC 120Ohm Analog Switches BREAK-BEFORE-MAKE MAX4551 16 Pins 1nA 5V 16-SSOP (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-SSOP (0.154, 3.90mm Width)
Number of Pins	16
Operating Temperature	0°C~70°C TA
Packaging	Tape & Reel (TR)
Published	1999
JESD-609 Code	e3
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
ECCN Code	EAR99
Resistance	120Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	762mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	5V
Terminal Pitch	0.635mm
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	MAX4551
Output	SEPARATE OUTPUT
Pin Count	16
Operating Supply Voltage	5V
Number of Channels	1
Number of Circuits	4
Max Supply Voltage	12V
Min Supply Voltage	2V
Operating Supply Current	1μA
Nominal Supply Current	50nA
Max Supply Current	1μA
Throw Configuration	SPST
Turn On Delay Time	350 ns
Voltage - Supply, Single/Dual (±)	2V~12V ±2V~6V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-5V
Turn-Off Delay Time	250 ns
Max Dual Supply Voltage	6V
On-State Resistance (Max)	120Ohm
Min Dual Supply Voltage	2V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	90 dB
Current - Leakage (IS(off)) (Max)	1nA
Channel Capacitance (CS(off), CD(off))	3.5pF 3pF
On-state Resistance Match-Nom	1Ohm
Switch Circuit	SPST - NC
Switch Time (Ton, Toff) (Max)	110ns, 90ns
Charge Injection	2pC
Channel-to-Channel Matching (ΔRon)	1 Ω
Crosstalk	-90dB @ 100kHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	110ns
Switch-off Time-Max	90ns
Normal Position	NO
Height Seated (Max)	1.75mm
Width	3.9mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant

MAX4551CEE+T Overview

Presented in 16-SSOP (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. It is mounted in the position Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operating temperature extended to 0°C~70°C TA. Total terminations are 16. High-quality output is provided by the electronic component's 1 channels. With a 5V voltage supply, the electrical component should be turned on and run. Into the electrical component body are injected 16 pins. Based on SPST - NC switching circuits, these analog multiplexers work. 4 circuits are used in this analogue multiplexer. Look for analog switch ic variants by searching with MAX4551. In this multiplexer, the internal resistance is 120Ohm. You can find the functions of the 16 pins in the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. A voltage higher than 12V should not normally be supplied to the switches. Analogue multiplexers of the Dual, Single supply type that are cost-effective. 2V is the lowest voltage the electrical component should receive. 1μA current would be enough for this multiplexer to operate. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. There is no problem with using dual supply voltage, but it should not exceed 6V. The voltage should be at least 2V if you are using dual power supplies. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. The electronic component can function from 5V.