MAX4551CPE
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 120Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4551 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDIP-T16 |
| Power Supplies | 3/5/+-5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Throw Configuration | SPST |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±2V~6V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 120Ohm |
| Min Dual Supply Voltage | 2V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 3.5pF 3pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 110ns, 90ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 125ns |
| Switch-off Time-Max | 100ns |
| Normal Position | NO |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4551CPE Overview
Presented in 16-DIP (0.300, 7.62mm), this electrical component is convenient for overseas shipping. High reliability is achieved by using advanced packaging method Tube. Through Hole is where this multiplexer is located. Multiplexer and demultiplexer circuits have a number 1:1. Temperatures around 0°C~70°C TA are extended for operation. There are 16 terminations totally. This electronic part offers high-quality output due to its 1 channels. An 5V voltage supply should allow the electrical part to be turned on and run. There is an electrical component included in the 16 series. On the other hand, analog switches can be constructed using SPST - NC switching circuits. There are 4 circuits in this switch device. Look for analog switch ic variants by searching with MAX4551. Internally, this switch multiplexer has a resistance of 120Ohm. The analog multiplexer shown here is a typical Multiplexer or Switches. Multiplexers should not be powered above 12V in normal situations. The analog switch ic is of the Dual, Single supply type and is cost-effective. The lowest voltage fed to the electronic component should be 2V. This digital switch can be operated with a current of 1μA. Despite this switch's dual supply capability, its voltage should not exceed 6V. In the case of dual power supplies, you should connect at least 2V. It is possible to use SEPARATE OUTPUT outputs on this digital multiplexer.
MAX4551CPE Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
MAX4551CPE Applications
There are a lot of Maxim Integrated MAX4551CPE Analog Switches & Multiplexers ICs applications.
- E1 Network Equipment
- Microprocessor Controlled Analog Systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- Avionics test equipment
- SONET/SDH ADM
- FTTH
- Sample-and-hold systems
- Medical
- Routers
- Microwave transmission systems
