MAX4551CSE
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 120Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4551 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 3/5/+-5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±2V~6V |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 120Ohm |
| Min Dual Supply Voltage | 2V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 3.5pF 3pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 110ns, 90ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 125ns |
| Switch-off Time-Max | 100ns |
| Normal Position | NO |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4551CSE Overview
The electronic component is convenient to ship overseas because it is packed in a 16-SOIC (0.154, 3.90mm Width). This high-reliability packaging method uses advanced packaging methods Tube. In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have a number of circuits 1:1. Extended operating temperature around 0°C~70°C TA. In total, there are 16 terminations. A high-quality output is provided by the electrical component's 1 channels. Powered by a 5V voltage supply, the electrical part should be switched on and run. A total of 16 pins are injected into the electrical part body. Unlike digital switches, these are based on SPST - NC switching circuits. Circuits number 4 make up this analogue multiplexer. Look for analog switch ic variants by searching with MAX4551. As far as internal resistance is concerned, it has 120Ohm. For details about the functions of 16 pins, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 12V. 2V should be the lowest voltage fed to the electronic component. For this switch, a dual supply voltage is feasible, but it must not exceed 6VYou should attach at least 2V voltage if you are using dual power supply. The analog switch ic utilizes SEPARATE OUTPUT outputs in total.
MAX4551CSE Features
1 Channels
Switch Circuit: SPST - NC
MAX4551CSE Applications
There are a lot of Maxim Integrated MAX4551CSE Analog Switches & Multiplexers ICs applications.
- ISDN NT1/TA
- Data Acquisition Systems
- Sample hold systems
- SDH
- CSU
- Industrial
- PBX interfaces
- Imaging
- FTTH
- Avionics
