MAX4551ESE

110ns, 90ns SPST - NC 120Ohm Analog Switches BREAK-BEFORE-MAKE MAX4551 16 Pins 1nA 5V 16-SOIC (0.154, 3.90mm Width)

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX4551ESE
Package: 16-SOIC (0.154, 3.90mm Width)
Datasheet: PDF
Stock: 206
Description: 110ns, 90ns SPST - NC 120Ohm Analog Switches BREAK-BEFORE-MAKE MAX4551 16 Pins 1nA 5V 16-SOIC (0.154, 3.90mm Width)(Kg)

Details

Tags

Parameters
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-SOIC (0.154, 3.90mm Width)
Number of Pins	16
Operating Temperature	-40°C~85°C TA
Packaging	Tube
Published	1999
JESD-609 Code	e0
Pbfree Code	no
Part Status	Obsolete
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
ECCN Code	EAR99
Resistance	120Ohm
Terminal Finish	Tin/Lead (Sn85Pb15)
Subcategory	Multiplexer or Switches
Max Power Dissipation	696mW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	240
Number of Functions	4
Supply Voltage	5V
Terminal Pitch	1.27mm
Time@Peak Reflow Temperature-Max (s)	20
Base Part Number	MAX4551
Output	SEPARATE OUTPUT
Pin Count	16
Power Supplies	3/5/+-5V
Number of Channels	4
Max Supply Voltage	6V
Min Supply Voltage	2V
Operating Supply Current	1μA
Nominal Supply Current	50nA
Max Supply Current	1μA
Throw Configuration	SPST
Turn On Delay Time	110 ns
Voltage - Supply, Single/Dual (±)	2V~12V ±2V~6V
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-5V
Turn-Off Delay Time	90 ns
Max Dual Supply Voltage	6V
On-State Resistance (Max)	120Ohm
Min Dual Supply Voltage	2V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	90 dB
Current - Leakage (IS(off)) (Max)	1nA
Channel Capacitance (CS(off), CD(off))	3.5pF 3pF
On-state Resistance Match-Nom	1Ohm
Switch Circuit	SPST - NC
Switch Time (Ton, Toff) (Max)	110ns, 90ns
Charge Injection	2pC
Channel-to-Channel Matching (ΔRon)	1 Ω
Crosstalk	-90dB @ 100kHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	125ns
Switch-off Time-Max	100ns
Normal Position	NO
Height Seated (Max)	1.75mm
Length	9.9mm
Width	3.9mm
Radiation Hardening	No
REACH SVHC	Unknown
RoHS Status	Non-RoHS Compliant
Lead Free	Contains Lead

MAX4551ESE Overview

The electronic component is convenient to ship overseas because it is packed in a 16-SOIC (0.154, 3.90mm Width). High reliability is achieved by using advanced packaging method Tube. This analog switch is mounted in Surface Mount. There is 1:1 ratio between the number of multiplexers and demultiplexers. An extended operating temperature of -40°C~85°C TA degrees Celsius. A total of 16 terminations have been recorded. A 4 channel electronic part produces high-quality output. Turning on and running the electrical part should be easy with a 5V voltage supply. 16 pins are injected to the electronic part body. SPST - NC switching circuits are used in these analog switch ics. Try searching for the analog switch ic with MAX4551 if you are looking for variants. It has an internal resistance of 120Ohm. The datasheets for the 16 pins explain the functions. Multiplexer or Switches is a typical switch device. Multiplexers should not be powered above 6V in normal situations. A analog switch ic that has a cost-effective Dual, Single supply type. There should be 2V voltage fed to the electrical part below 2V. It would be sufficient to run this analogue multiplexer with 1μA current. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 6V. The voltage should be at least 2V if you are using dual power supplies. In this switch multiplexer, there are SEPARATE OUTPUT outputs available.