MAX4551ESE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 120Ohm |
| Terminal Finish | MATTE TIN |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Base Part Number | MAX4551 |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 50nA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 350 ns |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±2V~6V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 120Ohm |
| Min Dual Supply Voltage | 2V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 3.5pF 3pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 110ns, 90ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -90dB @ 100kHz |
| Switch-on Time-Max | 110ns |
| Switch-off Time-Max | 90ns |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4551ESE+T Overview
This electronic part is conveniently packaged in 16-SOIC (0.154, 3.90mm Width), making it easy to ship abroad. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. Mounted in Surface Mount is this multiplexer. 1:1 is the ratio between multiplexers and demultiplexers. Operating temperature extended to -40°C~85°C TA. There are 16 terminations totally. The electronic part delivers high-quality output through its 1 channels. With a 5V voltage supply, the electrical component should be turned on and run. This electrical component is included in the 16 series of products. The analog switch ics are built using SPST - NC switching circuits. A total of 4 circuits make up this switch device. Try searching for MAX4551 variants of the analog switch ic. There is 120Ohm internal resistance in this digital multiplexer. It is generally not recommended to supply a voltage higher than 12V to the switch device in normal circumstances. Analog switch ics with Dual, Single supply type are cost-effective. In order for the electronic part to function properly, the lowest voltage should be 2V. The analogue multiplexer could operate on 1μA current. When the digital multiplexer is charged above 1μA, damage can occur. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 6V. You should attach at least 2V voltage if you are using dual power supply. It can operate from 5V operating voltages.
MAX4551ESE+T Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
MAX4551ESE+T Applications
There are a lot of Maxim Integrated MAX4551ESE+T Analog Switches & Multiplexers ICs applications.
- Industrial and process control systems
- Data switching
- Precision test equipment
- Remote Powered Equipment
- Multiplexers
- Audio signal routing
- PBX interfaces
- Frame Relay Equipment
- ISDN NT1/TA
- Digital cross connects (DSX-1)
