MAX4552CPE
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 120Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4552 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 3/5/+-5V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 6V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 50nA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 110 ns |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±2V~6V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 90 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 120Ohm |
| Min Dual Supply Voltage | 2V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 90 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 3.5pF 3pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 110ns, 90ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -90dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 125ns |
| Switch-off Time-Max | 100ns |
| Normal Position | NC |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4552CPE Overview
As the electronic part is packed in 16-DIP (0.300, 7.62mm), international shipping is convenient. High reliability is provided by advanced packaging method Tube. This analog switch is mounted in Through Hole. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operational temperature extended around 0°C~70°C TA. Totally, there are 16 terminations. High-quality output is provided by the electronic component's 1 channels. It is safe to turn on and run the electronic component with a 5V voltage supply. 16 pins are injected to the electronic part body. Circuits based on SPST - NO switching are used to construct these analog switch ics. The multiplexer consists of 4 circuits. Look for analog switch ic variants by searching with MAX4552. Internally, this switch multiplexer has a resistance of 120Ohm. For details about the functions of 16 pins, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. A voltage higher than 6V should not normally be supplied to the switches. A cost-effective Dual, Single supply type analogue multiplexer. 2V is the lowest voltage that should be fed to the electronic electronic part. For this multiplexer to operate, 1μA current would be sufficient. Putting voltage greater than 1μA on the multiplexer may cause damage. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 6V. A dual power supply should have at least 2V voltage attached. The digital multiplexer has SEPARATE OUTPUT outputs that can be used.
MAX4552CPE Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
MAX4552CPE Applications
There are a lot of Maxim Integrated MAX4552CPE Analog Switches & Multiplexers ICs applications.
- MP3 players
- CSU
- Voice over IP/DSL – Integrated Access Devices, Smart
- High-Voltage
- Battery Powered Instruments
- Digital cross connects (DSX-1)
- Imaging
- Avionics
- Industrial
- Video signal routing
