Parameters |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
1999 |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
120Ohm |
Terminal Finish |
Tin/Lead (Sn85Pb15) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
696mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
4 |
Supply Voltage |
5V |
Terminal Pitch |
1.27mm |
Time@Peak Reflow Temperature-Max (s) |
20 |
Base Part Number |
MAX4552 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Power Supplies |
3/5/+-5V |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
6V |
Min Supply Voltage |
2V |
Operating Supply Current |
1μA |
Nominal Supply Current |
50nA |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
110 ns |
Voltage - Supply, Single/Dual (±) |
2V~12V ±2V~6V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
90 ns |
Max Dual Supply Voltage |
6V |
On-State Resistance (Max) |
120Ohm |
Min Dual Supply Voltage |
2V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
90 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
3.5pF 3pF |
On-state Resistance Match-Nom |
1Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
110ns, 90ns |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
1 Ω |
Crosstalk |
-90dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
125ns |
Switch-off Time-Max |
100ns |
Normal Position |
NC |
Height Seated (Max) |
1.75mm |
Length |
9.9mm |
Width |
3.9mm |
Radiation Hardening |
No |
REACH SVHC |
Unknown |
RoHS Status |
Non-RoHS Compliant |
MAX4552ESE Overview
As the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. Advanced packaging method Tube is used to provide high reliability. It is mounted in the position Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operational temperature extended around -40°C~85°C TA. The total number of terminations is 16. This electronic part offers high-quality output due to its 1 channels. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. Based on SPST - NO switching circuits, these analog multiplexers work. There are 4 circuits in this switch device. Use MAX4552 to search for variants of the digital switches. In this multiplexer, the internal resistance is 120Ohm. For functions related to 16 pins, please refer to the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 6V. A cost-effective Dual, Single supply type analogue multiplexer. A low voltage of 2V should be applied to the electronic component. In order to operate this switch device, it would need a current of 1μA. The analogue multiplexer may be damaged if voltage is greater than 1μA. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 6V. A dual power supply should have at least 2V voltage attached. In this switch multiplexer, there are SEPARATE OUTPUT outputs available.
MAX4552ESE Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
MAX4552ESE Applications
There are a lot of Maxim Integrated MAX4552ESE Analog Switches & Multiplexers ICs applications.
- E1 Network Equipment
- Transmit
- Video signal routing
- Avionics
- Fiber In The Loop (FITL)
- Residential Gateways, Home Gateway/Router
- SDH
- Precision test equipment
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Fiber to the Home