Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
1999 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
120Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
696mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
5V |
Terminal Pitch |
1.27mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
MAX4553 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
JESD-30 Code |
R-PDSO-G16 |
Power Supplies |
3/5/+-5V |
Number of Channels |
1 |
Number of Circuits |
4 |
Max Supply Voltage |
6V |
Min Supply Voltage |
2V |
Operating Supply Current |
1μA |
Nominal Supply Current |
50nA |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
110 ns |
Voltage - Supply, Single/Dual (±) |
2V~12V ±2V~6V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
90 ns |
Max Dual Supply Voltage |
6V |
On-State Resistance (Max) |
120Ohm |
Min Dual Supply Voltage |
2V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
90 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
3.5pF 3pF |
On-state Resistance Match-Nom |
1Ohm |
Switch Circuit |
SPST - NO/NC |
Switch Time (Ton, Toff) (Max) |
110ns, 90ns |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
1 Ω |
Crosstalk |
-90dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Height Seated (Max) |
1.75mm |
Length |
9.9mm |
Width |
3.9mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
MAX4553ESE+ Overview
Shipping overseas is convenient with the electronic component packed in 16-SOIC (0.154, 3.90mm Width). Advanced packaging method Tube is used to provide high reliability. There is an analog multiplexer mounted in position Surface Mount. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operational temperature extended around -40°C~85°C TA. The total number of terminations is 16. As a result of its 1 channels, this electronic component provides high-quality output. When the electronic component is given a voltage of 5V, it should be turned on and run. The electronic part body is injected with 16 pins. A SPST - NO/NC switching circuit is used for these analog switches. 4 circuits are used in this analogue multiplexer. Try searching for MAX4553 variants of the analog switch ic. Internally, this switch multiplexer has a resistance of 120Ohm. This switch device is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 6V. Dual, Single supply type digital switch with a low cost. 2V is the lowest voltage that should be fed to the electronic electronic part. It would be sufficient to run this analogue multiplexer with 1μA current. Put voltage above 1μA on the multiplexer to cause damage. Despite this switch's dual supply capability, its voltage should not exceed 6V. It is recommended that you attach at least 2V to your dual power supply. The digital multiplexer has SEPARATE OUTPUT outputs that can be used.
MAX4553ESE+ Features
1 Channels
Switch Circuit: SPST - NO/NC
1μA Supply Current
MAX4553ESE+ Applications
There are a lot of Maxim Integrated MAX4553ESE+ Analog Switches & Multiplexers ICs applications.
- Industrial
- Voice over IP/DSL – Integrated Access Devices, Smart
- Microprocessor Controlled Analog Systems
- MP3 players
- PBXs
- Multi-Line E1 Interface Cards
- USB 1.1 signal switching circuits
- Communications systems
- SONET
- High reliability control systems