MAX4558CPE
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Weight | 1.627801g |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 160Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4558 |
| Pin Count | 16 |
| Operating Supply Voltage | 9V |
| Power Supplies | 3/3.3/5V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Max Supply Current | 1μA |
| Propagation Delay | 150 ns |
| Turn On Delay Time | 350 ns |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±2V~6V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 160Ohm |
| Min Dual Supply Voltage | 2V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 96 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 2.5pF 10pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Time (Ton, Toff) (Max) | 150ns, 120ns |
| Charge Injection | 2.4pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -93dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Height | 4.45mm |
| Length | 19.43mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4558CPE Overview
Shipping overseas is convenient due to the electrical component's packing in 16-DIP (0.300, 7.62mm). High reliability is provided by advanced packaging method Tube. The multiplexer is located in Through Hole. Multiplexers and demultiplexers have the same number of circuits 8:1. Around 0°C~70°C TA is the extended operating temperature. 16 terminations have been made so far. This electronic part offers high-quality output due to its 8 channels. Powered by a 5V voltage supply, the electrical part should be switched on and run. An electrical component of this type can be found in the 16 series. A total of 1 circuits make up this switch device. If you are looking for variants of the digital switch, trying search with MAX4558. A 160Ohm internal resistance characterizes this multiplexer. You can find the functions of the 16 pins in the datasheets. This switch device is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 12V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. A low voltage of 2V should be applied to the electronic component. The analogue multiplexer may be damaged if voltage is greater than 1μA. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 6V. A dual power supply should have at least 2V voltage attached. Integrated with SINGLE-ENDED MULTIPLEXER analog IC. There is a voltage range of 9V operating voltages for the electrical part.
MAX4558CPE Features
8 Channels
MAX4558CPE Applications
There are a lot of Maxim Integrated MAX4558CPE Analog Switches & Multiplexers ICs applications.
- High-Voltage
- Microprocessor controlled systems
- Cellular phones
- Relay replacements
- USB 1.1 signal switching circuits
- Video signal routing
- PDAs
- Audio and video switching
- Cable PC
- Automatic test equipment
