MAX4558CSE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Weight | 143.703733mg |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 220Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MAX4558 |
| Pin Count | 16 |
| Operating Supply Voltage | 9V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Propagation Delay | 150 ns |
| Turn On Delay Time | 350 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±2V~6V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 160Ohm |
| Min Dual Supply Voltage | 2V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 96 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 2.5pF 10pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Time (Ton, Toff) (Max) | 150ns, 120ns |
| Charge Injection | 2.4pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -93dB @ 100kHz |
| Height | 1.5mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4558CSE+T Overview
Presented in 16-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have a number of circuits 8:1. The operating temperature is extended to around 0°C~70°C TA. Total terminations are 16. As a result of its 8 channels, this electronic component provides high-quality output. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. An electrical component like this is included in the 16 series. There are 1 circuits in this switch device. Search with MAX4558 if you are looking for analog multiplexer variants. This digital multiplexer has 220Ohm internal resistance. For details about the functions of 16 pins, please refer to the datasheets. Users shouldn't supply more than 12V voltage to the switch device. An effective Dual, Single supply digital multiplexer. In order for the electronic part to function properly, the lowest voltage should be 2V. 1μA current would be enough for this multiplexer to operate. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. If put voltage greater than 6V on the multiplexer, damage may be caused to the device. You should attach at least 2V voltage if you are using dual power supply. This electrical part is compatible with 9V operating voltages.
MAX4558CSE+T Features
8 Channels
1μA Supply Current
MAX4558CSE+T Applications
There are a lot of Maxim Integrated MAX4558CSE+T Analog Switches & Multiplexers ICs applications.
- Channel Banks
- E1 Multiplexer
- Mechanical reed relay replacement
- Microprocessor Controlled Analog Systems
- Communication systems
- Access Concentrators
- Multi-Line E1 Interface Cards
- CSU
- PDH Multiplexers
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
