Parameters |
Mounting Type |
Through Hole |
Package / Case |
16-DIP (0.300, 7.62mm) |
Surface Mount |
NO |
Number of Pins |
16 |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tube |
Published |
1999 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
160Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
842mW |
Technology |
CMOS |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
5V |
Base Part Number |
MAX4559 |
Pin Count |
16 |
Operating Supply Voltage |
9V |
Power Supplies |
3/3.3/5V |
Number of Channels |
4 |
Number of Circuits |
2 |
Max Supply Voltage |
12V |
Min Supply Voltage |
2V |
Analog IC - Other Type |
DIFFERENTIAL MULTIPLEXER |
Max Supply Current |
1μA |
Propagation Delay |
150 ns |
Turn On Delay Time |
350 ns |
Voltage - Supply, Single/Dual (±) |
2V~12V ±2V~6V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
250 ns |
Max Dual Supply Voltage |
6V |
On-State Resistance (Max) |
160Ohm |
Min Dual Supply Voltage |
2V |
Multiplexer/Demultiplexer Circuit |
4:1 |
Off-state Isolation-Nom |
96 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
2.5pF 6pF |
On-state Resistance Match-Nom |
2Ohm |
Switch Circuit |
SP4T |
Switch Time (Ton, Toff) (Max) |
150ns, 120ns |
Charge Injection |
2.4pC |
Channel-to-Channel Matching (ΔRon) |
2 Ω |
Crosstalk |
-93dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Signal Current-Max |
0.01A |
Length |
19.175mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
MAX4559CPE+ Overview
The electronic component is convenient to ship overseas because it is packed in a 16-DIP (0.300, 7.62mm). The advanced packaging method Tube provides high reliability. In Through Hole, this analog switch is mounted. Multiplexers and demultiplexers have a number of circuits 4:1. The operating temperature is extended to around 0°C~70°C TA. In total, 16 terminations have occurred. As a result of its 4 channels, this electronic component provides high-quality output. An 5V voltage supply should allow the electrical part to be turned on and run. A total of 16 pins are injected into the electrical part body. Unlike digital switches, these are based on SP4T switching circuits. A total of 2 circuits make up this switch device. Search with MAX4559 if you are looking for analog multiplexer variants. There is 160Ohm internal resistance in this digital multiplexer. For functions related to 16 pins, please refer to the datasheets. Multiplexer or Switches is a typical switch device. In normalcircumstances, users should not exceed 12V volts for the multiplexer. Digital switch that provides Dual, Single power at a cost-effective price. A low voltage of 2V should be applied to the electronic component. It may damage the digital multiplexer if the voltage is higher than 1μA. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 6V. With dual power supplies, you should attach at least 2V. Integrated with DIFFERENTIAL MULTIPLEXER analog IC. There is a voltage range of 9V operating voltages for the electrical part.
MAX4559CPE+ Features
4 Channels
Switch Circuit: SP4T
MAX4559CPE+ Applications
There are a lot of Maxim Integrated MAX4559CPE+ Analog Switches & Multiplexers ICs applications.
- Signal routing between systems
- DSLAMs
- New designs requiring multiplexer functions
- Public switching systems
- CSU
- SDH/SONET multiplexers
- High reliability control systems
- Fiber In The Loop (FITL)
- Voice over IP/DSL – Integrated Access Devices, Smart
- Automatic test equipment