MAX4559CSE
| Parameters | |
|---|---|
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 160Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4559 |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Operating Supply Voltage | 9V |
| Power Supplies | 3/3.3/5V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Propagation Delay | 150 ns |
| Turn On Delay Time | 350 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±2V~6V |
| Supply Type | Dual, Single |
| Supply Current-Max (Isup) | 0.01mA |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 250 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 160Ohm |
| Min Dual Supply Voltage | 2V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 96 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 2.5pF 6pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 150ns, 120ns |
| Charge Injection | 2.4pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -93dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.01A |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
MAX4559CSE Overview
Shipping overseas is convenient with the electronic component packed in 16-SOIC (0.154, 3.90mm Width). High reliability is achieved by using advanced packaging method Tube. Mounted in Surface Mount is this multiplexer. Multiplexers and demultiplexers have a number of circuits 4:1. Operational temperature extended around 0°C~70°C TA. In total, 16 terminations have occurred. A 4 channel electronic part produces high-quality output. With a 5V voltage supply, the electrical component should be turned on and run. It is part of the design of the 16 series that this electronic component is included. A SP4T switching circuit is used for these analog switches. It consists of 2 circuits. Try searching for MAX4559 variants of the analog switch ic. An switch multiplexer with 160Ohm internal resistance has a value of 160Ohm. It is generally not recommended to supply a voltage higher than 12V to the switch device in normal circumstances. A cost-effective Dual, Single supply type analogue multiplexer. In order for the electronic part to function properly, the lowest voltage should be 2V. This multiplexer would work with 1μA current. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 6V. It is recommended that you attach at least 2V to your dual power supply. 9V operating voltages are supported by the electronic component.
MAX4559CSE Features
4 Channels
Switch Circuit: SP4T
1μA Supply Current
MAX4559CSE Applications
There are a lot of Maxim Integrated MAX4559CSE Analog Switches & Multiplexers ICs applications.
- Data Acquisition Systems
- High speed data transmission line cards
- CSU
- High reliability control systems
- Sample-and-hold systems
- Frame Relay Equipment
- PBX interfaces
- Industrial
- Remote Powered Equipment
- Existing multiplexer applications (both fault-protected and nonfault-protected)
