MAX4560CEE+T
| Parameters | |
|---|---|
| Number of Circuits | 3 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 10μA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 250 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±2V~6V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 350 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 160Ohm |
| Min Dual Supply Voltage | 2V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 96 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 2pF 4pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 150ns, 120ns |
| Charge Injection | 2.4pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -93dB @ 100kHz |
| Switch-on Time-Max | 150ns |
| Switch-off Time-Max | 120ns |
| Height Seated (Max) | 1.75mm |
| Length | 4.89mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 220Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 3 |
| Supply Voltage | 5V |
| Base Part Number | MAX4560 |
| Pin Count | 16 |
| Operating Supply Voltage | 6V |
| Number of Channels | 1 |
MAX4560CEE+T Overview
Due to its 16-SSOP (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. Multiplexer and demultiplexer circuits have a number 2:1. Around 0°C~70°C TA is the extended operating temperature. In total, there have been 16 terminations. As a result of its 1 channels, this electronic component provides high-quality output. When a voltage supply of 5V is used, the electronic component should be turned on and run. It is part of the design of the 16 series that this electronic component is included. Unlike digital switches, these are based on SPDT switching circuits. The circuits in this analogue multiplexer number 3. Using the MAX4560 search parameter, you can discover variants of the switch. A 220Ohm internal resistance characterizes this multiplexer. For functions related to 16 pins, please refer to the datasheets. In normalcircumstances, users should not exceed 12V volts for the multiplexer. The digital multiplexer has a low cost Dual, Single supply. In order for the electronic part to function properly, the lowest voltage should be 2V. The switch device would be able to operate with 1μA current. A voltage higher than 1μA may cause damage to the switch multiplexer. Despite this switch's dual supply capability, its voltage should not exceed 6V. You should attach at least 2V voltage if you are using dual power supply. Operating voltages of 6V are compatible with the electrical part.
MAX4560CEE+T Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
MAX4560CEE+T Applications
There are a lot of Maxim Integrated MAX4560CEE+T Analog Switches & Multiplexers ICs applications.
- Communication systems
- Access Concentrators
- Battery-powered systems
- Public switching systems
- PCMCIA cards
- Precision data acquisition
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- High-Voltage
- Residential Gateways, Home Gateway/Router
- Medical
