MAX4560CPE
| Parameters | |
|---|---|
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 96 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 2pF 4pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 150ns, 120ns |
| Charge Injection | 2.4pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -93dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.01A |
| Height Seated (Max) | 4.572mm |
| Length | 19.175mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 160Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 842mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 3 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4560 |
| Pin Count | 16 |
| Number of Channels | 1 |
| Number of Circuits | 3 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Max Supply Current | 1μA |
| Turn On Delay Time | 150 ns |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±2V~6V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 120 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 160Ohm |
| Min Dual Supply Voltage | 2V |
| Dual Supply Voltage | 5V |
MAX4560CPE Overview
The electrical component comes in 16-DIP (0.300, 7.62mm) packaging, which makes it convenient to ship overseas. High reliability is achieved by using advanced packaging method Tube. It is mounted in the position Through Hole. 2:1 is the ratio between multiplexers and demultiplexers. Operation at a temperature around 0°C~70°C TA. 16 terminations have been made so far. High-quality output is provided by the electronic component's 1 channels. An 5V voltage supply should allow the electrical part to be turned on and run. It is part of the design of the 16 series that this electronic component is included. Unlike digital switches, these are based on SPDT switching circuits. 3 circuits are used in this analogue multiplexer. Try searching for MAX4560 variants of the analog switch ic. It has an internal resistance of 160Ohm. To find out what the 16 pins do, please refer to the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. It is normally recommended that users do not supply the multiplexer with voltages higher than 12V. Analog switch ics with Dual, Single supply type are cost-effective. 2V is the lowest voltage that should be fed to the electronic electronic part. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. Despite this switch device's dual supply capability, its voltage should not exceed 6V. With dual power supplies, you should attach at least 2V.
MAX4560CPE Features
1 Channels
Switch Circuit: SPDT
MAX4560CPE Applications
There are a lot of Maxim Integrated MAX4560CPE Analog Switches & Multiplexers ICs applications.
- Remote wireless modules
- Avionics
- Microprocessor controlled systems
- Ultrasound
- RGB switches
- Microprocessor Controlled Analog Systems
- Low-Voltage
- Battery-powered systems
- FTTH
- Switching Systems
