Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SSOP (0.154, 3.90mm Width) |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
1999 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
220Ohm |
Terminal Finish |
Matte Tin (Sn) |
Max Power Dissipation |
640mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
3 |
Supply Voltage |
5V |
Base Part Number |
MAX4560 |
Pin Count |
16 |
Operating Supply Voltage |
6V |
Number of Channels |
1 |
Number of Circuits |
3 |
Max Supply Voltage |
12V |
Min Supply Voltage |
2V |
Operating Supply Current |
1μA |
Nominal Supply Current |
10μA |
Max Supply Current |
1μA |
Turn On Delay Time |
250 ns |
Logic Function |
Multiplexer |
Voltage - Supply, Single/Dual (±) |
2V~12V ±2V~6V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
350 ns |
Max Dual Supply Voltage |
6V |
On-State Resistance (Max) |
160Ohm |
Min Dual Supply Voltage |
2V |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
96 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
2pF 4pF |
On-state Resistance Match-Nom |
2Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
150ns, 120ns |
Charge Injection |
2.4pC |
Channel-to-Channel Matching (ΔRon) |
2 Ω |
Crosstalk |
-93dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
150ns |
Switch-off Time-Max |
120ns |
Signal Current-Max |
0.01A |
Height Seated (Max) |
1.75mm |
Length |
4.89mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
MAX4560EEE+ Overview
Shipping overseas is convenient due to the electrical component's packing in 16-SSOP (0.154, 3.90mm Width). The advanced packaging method Tube provides high reliability. The multiplexer is located in Surface Mount. 2:1 is the ratio between multiplexers and demultiplexers. Operational temperature extended around -40°C~85°C TA. In total, there are 16 terminations. A 1 channel electronic part produces high-quality output. An 5V voltage supply should allow the electrical part to be turned on and run. An electrical component of this type can be found in the 16 series. On the other hand, analog switches can be constructed using SPDT switching circuits. It consists of 3 circuits. Try searching with MAX4560 to find analog multiplexer variants. A 220Ohm internal resistance characterizes this multiplexer. You can find the functions of the 16 pins in the datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 12V. Analogue multiplexers of the Dual, Single supply type that are cost-effective. The lowest voltage the electronic part should receive is 2V. This digital switch can be operated with a current of 1μA. A digital multiplexer may suffer damage if voltage is applied above 1μA. For this switch, a dual supply voltage is feasible, but it must not exceed 6VWhen using dual power supplies, you should attach at least 2V. It can operate from 6V operating voltages.
MAX4560EEE+ Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
MAX4560EEE+ Applications
There are a lot of Maxim Integrated MAX4560EEE+ Analog Switches & Multiplexers ICs applications.
- MP3 players
- Medical
- Microprocessor controlled systems
- Avionics
- USB 1.1 signal switching circuits
- Mechanical reed relay replacement
- Precision instrumentation
- 65 V DACs
- Public switching systems
- Data Acquisition Systems