MAX4560ESE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 160Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 640mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 3 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Base Part Number | MAX4560 |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Operating Supply Voltage | 6V |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Number of Circuits | 3 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Nominal Supply Current | 10μA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 250 ns |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±2V~6V |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 350 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 160Ohm |
| Min Dual Supply Voltage | 2V |
| High Level Output Current | 10mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 96 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 2pF 4pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 150ns, 120ns |
| Charge Injection | 2.4pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -93dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 150ns |
| Switch-off Time-Max | 120ns |
| Signal Current-Max | 0.01A |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4560ESE+T Overview
Presented in 16-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. High reliability is achieved by using advanced packaging method Tape & Reel (TR). Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have the same number of circuits 2:1. Around -40°C~85°C TA is the extended operating temperature. In total, there are 16 terminations. A high-quality output is provided by the electrical component's 1 channels. A 5V voltage supply should turn on and run the electronic component. It is injected into the electrical part body with 16 pins. On the other hand, analog switches can be constructed using SPDT switching circuits. The multiplexer consists of 3 circuits. Search with MAX4560 if you are looking for analog multiplexer variants. An switch multiplexer with 160Ohm internal resistance has a value of 160Ohm. A analogue multiplexer of this type is a Multiplexer or Switches. In normalcircumstances, users should not exceed 12V volts for the multiplexer. 2V should be the lowest voltage fed to the electronic component. Put voltage above 1μA on the multiplexer to cause damage. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 6V. For dual power supplies, a voltage of at least 2V should be attached. Operating voltages of 6V are compatible with the electrical part.
MAX4560ESE+T Features
1 Channels
Switch Circuit: SPDT
MAX4560ESE+T Applications
There are a lot of Maxim Integrated MAX4560ESE+T Analog Switches & Multiplexers ICs applications.
- Switching Systems
- Video signal routing
- DSLAMs
- Public switching systems
- Communication systems
- Digital cross connects (DSX-1)
- Fiber In The Loop (FITL)
- High-Voltage
- Optical Applications
- Audio and video switching
