MAX4575ESA+
| Parameters | |
|---|---|
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4575 |
| Pin Count | 8 |
| Operating Supply Voltage | 9V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 10μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 100 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 250 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 70Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 45 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 20pF 12pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 80ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switch-on Time-Max | 150ns |
| Voltage - Supply, Single (V+) | 2V~12V |
| Height Seated (Max) | 1.75mm |
| Length | 4.9mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2000 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 120Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 330mW |
| Technology | CMOS |
| Terminal Position | DUAL |
MAX4575ESA+ Overview
Presented in 8-SOIC (0.154, 3.90mm Width), this electrical component is convenient for overseas shipping. High reliability is achieved by using advanced packaging method Tube. This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Operation at a temperature around -40°C~85°C TA. In total, there have been 8 terminations. Due to its 1 channels, the electrical component produces high-quality output. When the electronic component is given a voltage of 5V, it should be turned on and run. 8 pins are injected to the electronic part body. A SPST - NO switching circuit is used to build these analog multiplexers. 2 circuits are used in this analogue multiplexer. Try searching with MAX4575 to find analog multiplexer variants. In this multiplexer, the internal resistance is 120Ohm. The functions of 8 pins can be found in the datasheets. It is generally not recommended to supply a voltage higher than 12V to the switch device in normal circumstances. A analog switch ic that has a cost-effective Single supply type. The lowest voltage the electronic part should receive is 2V. For this digital switch to work, 1μA current would suffice. This analog switch requires a voltage of 2V~12V to drain from a single voltage supply. A voltage higher than 1μA may cause damage to the switch multiplexer. The electrical part can be operated at 9V voltage levels.
MAX4575ESA+ Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
-3db Bandwidth: 300MHz
MAX4575ESA+ Applications
There are a lot of Maxim Integrated MAX4575ESA+ Analog Switches & Multiplexers ICs applications.
- Avionics test equipment
- PBX interfaces
- Avionics and Military Systems
- RGB switches
- Video switching
- T1/E1 Terminals
- Industrial and process control systems
- Data switching
- Audio and video switching
- Cable PC
