MAX4575EUA+T
| Parameters | |
|---|---|
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4575 |
| Pin Count | 8 |
| Operating Supply Voltage | 9V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 10μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 100 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 250 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 70Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 45 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 20pF 12pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 150ns, 80ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switch-on Time-Max | 150ns |
| Voltage - Supply, Single (V+) | 2V~12V |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2000 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 70Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Max Power Dissipation | 330mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
MAX4575EUA+T Overview
Shipping overseas is convenient with the electronic component packed in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). High reliability is provided by advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Operating temperature around -40°C~85°C TA extended. There are 8 terminations totally. By its 1 channels, the electronic component provides high-quality output. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. There are 8 pins injected into the electronic part body. These analog multiplexers are built based on SPST - NO switching circuits. This multiplexer is composed of 2 circuits. Try searching for MAX4575 variants of the analog switch ic. As far as internal resistance is concerned, it has 70Ohm. Datasheets for functions of 8 pins are available. In normalcircumstances, users should not exceed 12V volts for the multiplexer. A analog switch ic that has a cost-effective Single supply type. 2V is the lowest voltage the electrical component should receive. An operating current of 1μA would be sufficient for this switch device. An analogue multiplexer drains from a single voltage supply at 2V~12V. When the digital multiplexer is charged above 1μA, damage can occur. Operating voltages of 9V are compatible with the electrical part.
MAX4575EUA+T Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
-3db Bandwidth: 300MHz
MAX4575EUA+T Applications
There are a lot of Maxim Integrated MAX4575EUA+T Analog Switches & Multiplexers ICs applications.
- New designs requiring multiplexer functions
- Signal routing between systems
- Automotive applications
- MP3 players
- Isolation
- Multi-Line E1 Interface Cards
- DSLAMs
- SDH/SONET multiplexers
- High reliability control systems
- Automatic test equipment
