MAX4576EUA+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2000 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 70Ohm |
| Terminal Finish | NICKEL PALLADIUM GOLD |
| Max Power Dissipation | 330mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4576 |
| Pin Count | 8 |
| Operating Supply Voltage | 9V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Nominal Supply Current | 10μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 100 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 250 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 70Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 45 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 20pF 12pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 150ns, 80ns |
| Charge Injection | 5pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switch-on Time-Max | 150ns |
| Voltage - Supply, Single (V+) | 2V~12V |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4576EUA+T Overview
The electronic component is convenient to ship overseas because it is packed in a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). Advanced packaging method Tape & Reel (TR) is used to provide high reliability. A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. An extended operating temperature of -40°C~85°C TA degrees Celsius. Total terminations are 8. By its 1 channels, the electronic component provides high-quality output. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. Electronic part bodies are injected with 8 pins. The analog switch ics are built using SPST - NC switching circuits. The multiplexer consists of 2 circuits. Search with MAX4576 if you are looking for analog multiplexer variants. An switch multiplexer with 70Ohm internal resistance has a value of 70Ohm. Datasheets for functions of 8 pins are available. Multiplexers should not be powered above 12V in normal situations. Digital switch that provides Single power at a cost-effective price. It is recommended to use 2V as the lowest voltage for the electrical part. Draining from a single voltage supply, this analog switch requires a voltage of 2V~12V. Putting voltage greater than 1μA on the multiplexer may cause damage. A voltage of 9V can be used to operate the electronic component.
MAX4576EUA+T Features
1 Channels
Switch Circuit: SPST - NC
-3db Bandwidth: 300MHz
MAX4576EUA+T Applications
There are a lot of Maxim Integrated MAX4576EUA+T Analog Switches & Multiplexers ICs applications.
- New designs requiring multiplexer functions
- Microprocessor controlled systems
- Fiber to the Home
- SDH
- Audio and video signal routing
- Digital Cross-Connects
- Video switching
- CSU
- USB 1.1 signal switching circuits
- E1 Network Equipment
