MAX4581ESE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 450Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4581 |
| Pin Count | 16 |
| Operating Supply Voltage | 9V |
| Power Supplies | 3/5/+-5V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Propagation Delay | 200 ns |
| Turn On Delay Time | 300 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±2V~6V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 80Ohm |
| Min Dual Supply Voltage | 2V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 73 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 18pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Time (Ton, Toff) (Max) | 200ns, 100ns |
| Charge Injection | 0.5pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -78dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.02A |
| Height | 1.5mm |
| Length | 10mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
MAX4581ESE+ Overview
As the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. To ensure high reliability, a new packaging method Tube is used. Multiplexers like this are mounted in the Surface Mount position. Multiplexers and demultiplexers have a ratio of 8:1. Operation at a temperature around -40°C~85°C TA. In total, there have been 16 terminations. The electronic part provides high-quality output because it has 8 channels. Powered by a 5V voltage supply, the electrical part should be switched on and run. An electrical component like this is included in the 16 series. There are 1 circuits in this multiplexer. Look for analog switch ic variants by searching with MAX4581. In this multiplexer, the internal resistance is 450Ohm. For details about the functions of 16 pins, please refer to the datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 12V. Analog switch ics with Dual, Single supply type are cost-effective. There should be 2V voltage fed to the electrical part below 2V. For this digital switch to work, 1μA current would suffice. Despite this switch's dual supply capability, its voltage should not exceed 6V. If you are using dual power supplies, you should attach at least 2V. Operating voltages of 9V are compatible with the electrical part.
MAX4581ESE+ Features
8 Channels
1μA Supply Current
MAX4581ESE+ Applications
There are a lot of Maxim Integrated MAX4581ESE+ Analog Switches & Multiplexers ICs applications.
- HDTV
- High-Voltage
- Private Branch Exchange (PBX)
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Isolation
- Mechanical reed relay replacement
- High speed data transmission line cards
- Public switching systems
- Audio/video switches
