MAX4581ESE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 80Ohm |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4581 |
| Pin Count | 16 |
| Operating Supply Voltage | 9V |
| Power Supplies | 3/5/+-5V |
| Number of Channels | 8 |
| Number of Circuits | 1 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Propagation Delay | 200 ns |
| Turn On Delay Time | 300 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±2V~6V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 80Ohm |
| Min Dual Supply Voltage | 2V |
| High Level Output Current | 20mA |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 73 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 18pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Time (Ton, Toff) (Max) | 200ns, 100ns |
| Charge Injection | 0.5pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -78dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.02A |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4581ESE+T Overview
As the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. A switch device like this is mounted in Surface Mount. There is 8:1 ratio between the number of multiplexers and demultiplexers. Operation at a temperature around -40°C~85°C TA. Total terminations are 16. A high-quality output is provided by the electrical component's 8 channels. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. This electronic part can be found in the 16 series. The circuits in this analogue multiplexer number 1. Look for analog switch ic variants by searching with MAX4581. A 80Ohm internal resistance characterizes this multiplexer. Datasheets for functions of 16 pins are available. Users shouldn't supply more than 12V voltage to the switch device. A cost-effective Dual, Single supply type analogue multiplexer. 2V is the lowest voltage that should be fed to the electronic electronic part. This multiplexer would work with 1μA current. For this multiplexer, dual supply voltage is feasible, but it should not exceed 6V. You should attach at least 2V voltage if you are using dual power supply. 9V operating voltages can be used with this electrical part.
MAX4581ESE+T Features
8 Channels
1μA Supply Current
MAX4581ESE+T Applications
There are a lot of Maxim Integrated MAX4581ESE+T Analog Switches & Multiplexers ICs applications.
- Transmit
- MP3 players
- Medical Instrumentation
- Relay Replacement
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Automatic test equipment
- FTTH
- SONET
- Battery Powered Systems
- Ultrasound
