MAX4582CSE
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 80Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4582 |
| Pin Count | 16 |
| Power Supplies | 3/5/+-5V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Propagation Delay | 200 ns |
| Turn On Delay Time | 200 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±2V~6V |
| Supply Type | Dual, Single |
| Supply Current-Max (Isup) | 0.01mA |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 80Ohm |
| Min Dual Supply Voltage | 2V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 74 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 10pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 200ns, 100ns |
| Charge Injection | 0.5pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -96dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4582CSE Overview
The electrical component comes in 16-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. This high-reliability packaging method uses advanced packaging methods Tube. Mounted in Surface Mount is this multiplexer. Multiplexers and demultiplexers have the same number of circuits 4:1. Operating temperature extended to 0°C~70°C TA. Total terminations are 16. A electrical component with 4 channels is capable of high-quality output. When the electronic component is given a voltage of 5V, it should be turned on and run. It is injected into the electrical part body with 16 pins. SP4T switching circuits are used in these analog switch ics. 2 circuits are used in this analogue multiplexer. Use MAX4582 to search for variants of the digital switches. Analog switches have 80Ohm internal resistance. The functions of 16 pins can be found in the datasheets. Multiplexers should not be powered above 12V in normal situations. The digital multiplexer has a low cost Dual, Single supply. 2V should be the lowest voltage fed to the electronic component. The switch device would be able to operate with 1μA current. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 6V. In the case of dual power supplies, you should connect at least 2V.
MAX4582CSE Features
4 Channels
Switch Circuit: SP4T
1μA Supply Current
MAX4582CSE Applications
There are a lot of Maxim Integrated MAX4582CSE Analog Switches & Multiplexers ICs applications.
- Remote wireless modules
- Microprocessor controlled systems
- Switching Systems
- Isolation
- Audio signal routing
- Video switching
- Cell phones
- Residential Gateways, Home Gateway/Router
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Low-Voltage
