MAX4582EEE
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2007 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 80Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Max Power Dissipation | 667mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.635mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4582 |
| Pin Count | 16 |
| Operating Supply Voltage | 9V |
| Power Supplies | 3/5/+-5V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Propagation Delay | 200 ns |
| Turn On Delay Time | 300 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±2V~6V |
| Supply Type | Dual, Single |
| Supply Current-Max (Isup) | 0.01mA |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 80Ohm |
| Min Dual Supply Voltage | 2V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 74 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 10pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 200ns, 100ns |
| Charge Injection | 0.5pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -96dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 100ns |
| Height Seated (Max) | 1.73mm |
| Length | 4.89mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4582EEE Overview
The electrical component comes in 16-SSOP (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. This packaging method provides high reliability because it uses advanced packaging techniques. There is an analog multiplexer mounted in position Surface Mount. 4:1 is the ratio between multiplexers and demultiplexers. Extended operating temperature around -40°C~85°C TA. The total number of terminations is 16. High-quality output is provided by the electronic component's 4 channels. When the electronic component is given a voltage of 5V, it should be turned on and run. An electrical component of this type can be found in the 16 series. Circuits based on SP4T switching are used to construct these analog switch ics. Circuits number 2 make up this analogue multiplexer. Try searching for MAX4582 variants of the analog switch ic. It has an internal resistance of 80Ohm. Please refer to the datasheets for 16 pins functions. An abnormal situation would be for the switch device to be supplied with a voltage greater than 12V. Dual, Single supply type digital switch with a low cost. 2V should be the lowest voltage fed to the electronic component. 1μA current would be enough for this multiplexer to operate. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 6V. With dual power supplies, you should attach at least 2V. Operating voltages range from 9V.
MAX4582EEE Features
4 Channels
Switch Circuit: SP4T
1μA Supply Current
MAX4582EEE Applications
There are a lot of Maxim Integrated MAX4582EEE Analog Switches & Multiplexers ICs applications.
- E1 Network Equipment
- Cable Modem
- Communications systems
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Fiber In The Loop (FITL)
- Channelized and Unchannelized DS3 applications
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Voice over IP/DSL – Integrated Access Devices, Smart
- Private Branch Exchange (PBX)
- Data switching
