MAX4582ESE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2011 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 80Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4582 |
| Pin Count | 16 |
| Operating Supply Voltage | 9V |
| Power Supplies | 3/5/+-5V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Propagation Delay | 200 ns |
| Turn On Delay Time | 300 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±2V~6V |
| Supply Type | Dual, Single |
| Supply Current-Max (Isup) | 0.01mA |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 80Ohm |
| Min Dual Supply Voltage | 2V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 73 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 10pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 200ns, 100ns |
| Charge Injection | 0.5pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -96dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 100ns |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX4582ESE+ Overview
As the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. The advanced packaging method Tube provides high reliability. A switch device like this is mounted in Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 4:1. Operational temperature extended around -40°C~85°C TA. In total, 16 terminations have occurred. By its 4 channels, the electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 5V voltage supply. There is an electrical component included in the 16 series. A SP4T switching circuit is used for these analog switches. There are 2 circuits in this multiplexer. Look for analog switch ic variants by searching with MAX4582. It has an internal resistance of 80Ohm. The functions of 16 pins can be found in the datasheets. In a normalsituation, users should not supply the switches with voltage higher than 12V. A cost-effective Dual, Single supply type analogue multiplexer. It is recommended to use 2V as the lowest voltage for the electrical part. It would be sufficient to run this analogue multiplexer with 1μA current. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 6V. For dual power supplies, a voltage of at least 2V should be attached. Operating voltages range from 9V.
MAX4582ESE+ Features
4 Channels
Switch Circuit: SP4T
1μA Supply Current
MAX4582ESE+ Applications
There are a lot of Maxim Integrated MAX4582ESE+ Analog Switches & Multiplexers ICs applications.
- Medical
- ISDN NT1/TA
- Public switching systems
- Video signal routing
- Remote wireless modules
- Data Acquisition Systems
- DVD-R
- Cellular phones
- Imaging
- High speed data transmission line cards
