MAX4582ESE+T
| Parameters | |
|---|---|
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4582 |
| Pin Count | 16 |
| Operating Supply Voltage | 9V |
| Power Supplies | 3/5/+-5V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Propagation Delay | 200 ns |
| Turn On Delay Time | 300 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±2V~6V |
| Supply Type | Dual, Single |
| Supply Current-Max (Isup) | 0.01mA |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 80Ohm |
| Min Dual Supply Voltage | 2V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 73 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 10pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 200ns, 100ns |
| Charge Injection | 0.5pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -96dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 100ns |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 80Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
MAX4582ESE+T Overview
Shipping overseas is convenient with the electronic component packed in 16-SOIC (0.154, 3.90mm Width). High reliability is achieved by using advanced packaging method Tape & Reel (TR). The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have a ratio of 4:1. Operating temperature extended to -40°C~85°C TA. Total terminations are 16. Due to its 4 channels, the electrical component produces high-quality output. When the electronic component is given a voltage of 5V, it should be turned on and run. Into the electrical component body are injected 16 pins. The analog switch ics are built using SP4T switching circuits. There are 2 circuits in this switch device. Try searching with MAX4582 if you're looking for variants. The internal resistance of this digital multiplexer is 80Ohm. To find out what the 16 pins do, please refer to the datasheets. A voltage higher than 12V should not normally be supplied to the switches. Analogue multiplexer with a Dual, Single supply type that is cost-effective. It is recommended that the electrical component receives a voltage of 2V. This multiplexer would work with 1μA current. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 6V. A dual power supply should have at least 2V voltage attached. Operating voltages of 9V are compatible with the electrical part.
MAX4582ESE+T Features
4 Channels
Switch Circuit: SP4T
1μA Supply Current
MAX4582ESE+T Applications
There are a lot of Maxim Integrated MAX4582ESE+T Analog Switches & Multiplexers ICs applications.
- Industrial and process control systems
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Audio and video routing
- Remote wireless modules
- PBXs
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Modems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Fiber to the Home
- SONET/SDH ADM
