MAX4582EUE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2012 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 80Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 457mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4582 |
| Pin Count | 16 |
| Operating Supply Voltage | 9V |
| Power Supplies | 3/5/+-5V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Propagation Delay | 200 ns |
| Turn On Delay Time | 300 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±2V~6V |
| Supply Type | Dual, Single |
| Supply Current-Max (Isup) | 0.01mA |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 200 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 80Ohm |
| Min Dual Supply Voltage | 2V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 73 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 10pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 200ns, 100ns |
| Charge Injection | 0.5pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -96dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 100ns |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4582EUE+T Overview
As the electronic part is packed in 16-TSSOP (0.173, 4.40mm Width), international shipping is convenient. High reliability is achieved by using advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 4:1. Extended operating temperature around -40°C~85°C TA. In total, 16 terminations have occurred. A 4 channel electronic part produces high-quality output. Turning on and running the electrical part should be easy with a 5V voltage supply. The electronic part body is injected with 16 pins. A SP4T switching circuit is used to build these analog multiplexers. There are 2 circuits in this switch device. Use MAX4582 to search for variants of the digital switches. As far as internal resistance is concerned, it has 80Ohm. Datasheets for functions of 16 pins are available. It is normally recommended that users do not supply the multiplexer with voltages higher than 12V. The analog switch ic is of the Dual, Single supply type and is cost-effective. A low voltage of 2V should be applied to the electronic component. For this multiplexer to operate, 1μA current would be sufficient. There is no problem with using dual supply voltage, but it should not exceed 6V. A dual power supply should have at least 2V voltage attached. This electrical part is compatible with 9V operating voltages.
MAX4582EUE+T Features
4 Channels
Switch Circuit: SP4T
1μA Supply Current
MAX4582EUE+T Applications
There are a lot of Maxim Integrated MAX4582EUE+T Analog Switches & Multiplexers ICs applications.
- Sample hold systems
- Battery-powered systems
- Sample-and-hold systems
- SDH
- Cellular phones
- Audio and video switching
- Audio signal routing
- Automatic test equipment
- Data Acquisition Systems
- E1 Network Equipment
