Parameters |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2012 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
80Ohm |
Terminal Finish |
Matte Tin (Sn) |
Max Power Dissipation |
696mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
5V |
Base Part Number |
MAX4582 |
Pin Count |
16 |
JESD-30 Code |
R-PDSO-G16 |
Operating Supply Voltage |
12V |
Number of Channels |
4 |
Number of Circuits |
2 |
Max Supply Voltage |
12.6V |
Min Supply Voltage |
2V |
Operating Supply Current |
1μA |
Propagation Delay |
200 ns |
Turn On Delay Time |
200 ns |
Logic Function |
Multiplexer |
Supply Type |
Dual, Single |
Supply Current-Max (Isup) |
0.01mA |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
100 ns |
On-State Resistance (Max) |
80Ohm |
Multiplexer/Demultiplexer Circuit |
4:1 |
Off-state Isolation-Nom |
73 dB |
Current - Leakage (IS(off)) (Max) |
2nA |
Channel Capacitance (CS(off), CD(off)) |
4pF 10pF |
On-state Resistance Match-Nom |
1Ohm |
Switch Circuit |
SP4T |
Switch Time (Ton, Toff) (Max) |
200ns, 100ns |
Charge Injection |
0.5pC |
Channel-to-Channel Matching (ΔRon) |
1 Ω |
Crosstalk |
-96dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Voltage - Supply, Single (V+) |
2V~12V |
Height Seated (Max) |
1.75mm |
Length |
9.9mm |
Width |
3.9mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
MAX4582LESE+T Overview
As the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. This packaging method provides high reliability because it uses advanced packaging techniques. Mounted in Surface Mount is this multiplexer. Multiplexers and demultiplexers have a ratio of 4:1. Operational temperature extended around -40°C~85°C TA. Total terminations are 16. A high-quality output is provided by the electrical component's 4 channels. An 5V voltage supply should allow the electrical part to be turned on and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. These analog multiplexers are built based on SP4T switching circuits. A total of 2 circuits make up this switch device. Try searching with MAX4582 if you're looking for variants. It has an internal resistance of 80Ohm. normally, users should not supply switches with voltages higher than 12.6V. Dual, Single supply type digital switch with a low cost. A low voltage of 2V should be applied to the electronic component. This multiplexer would work with 1μA current. A voltage of 2V~12V is required for this switch device, which drains from a single voltage source. The electronic component can function from 12V.
MAX4582LESE+T Features
4 Channels
Switch Circuit: SP4T
1μA Supply Current
MAX4582LESE+T Applications
There are a lot of Maxim Integrated MAX4582LESE+T Analog Switches & Multiplexers ICs applications.
- Remote Powered Equipment
- Remote wireless modules
- Multiplexers
- Public switching systems
- Video signal routing
- Cellular phones
- Channel Banks
- DSUs
- Private Branch Exchange (PBX)
- RGB switches