Parameters |
On-state Resistance Match-Nom |
1Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
200ns, 100ns |
Charge Injection |
0.5pC |
Channel-to-Channel Matching (ΔRon) |
1 Ω |
Crosstalk |
-73dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Signal Current-Max |
0.02A |
Length |
4.89mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SSOP (0.154, 3.90mm Width) |
Number of Pins |
16 |
Operating Temperature |
0°C~70°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2012 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
80Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
696mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
3 |
Supply Voltage |
5V |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
MAX4583 |
Pin Count |
16 |
Operating Supply Voltage |
6V |
Number of Channels |
1 |
Number of Circuits |
3 |
Max Supply Voltage |
12V |
Min Supply Voltage |
2V |
Operating Supply Current |
1μA |
Max Supply Current |
1μA |
Turn On Delay Time |
200 ns |
Voltage - Supply, Single/Dual (±) |
2V~12V ±2V~6V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
100 ns |
Max Dual Supply Voltage |
6V |
On-State Resistance (Max) |
80Ohm |
Min Dual Supply Voltage |
2V |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
73 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
4pF 6pF |
MAX4583CEE+T Overview
Shipping overseas is convenient due to the electrical component's packing in 16-SSOP (0.154, 3.90mm Width). High reliability is provided by advanced packaging method Tape & Reel (TR). It is mounted in the position Surface Mount. Multiplexer and demultiplexer circuits have a number 2:1. Operating temperature around 0°C~70°C TA extended. Total terminations are 16. A 1 channel electronic part produces high-quality output. It is safe to turn on and run the electronic component with a 5V voltage supply. Into the electrical component body are injected 16 pins. Circuits based on SPDT switching are used to construct these analog switch ics. This multiplexer is composed of 3 circuits. If you are looking for variants of the digital switch, trying search with MAX4583. An switch multiplexer with 80Ohm internal resistance has a value of 80Ohm. Datasheets for functions of 16 pins are available. This switch device is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 12V. The analog switch ic is of the Dual, Single supply type and is cost-effective. 2V is the lowest voltage that should be fed to the electronic electronic part. An operating current of 1μA would be sufficient for this switch device. A digital multiplexer may suffer damage if voltage is applied above 1μA. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 6V. When using dual power supplies, you should attach at least 2V. 6V operating voltages are supported by the electronic component.
MAX4583CEE+T Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
MAX4583CEE+T Applications
There are a lot of Maxim Integrated MAX4583CEE+T Analog Switches & Multiplexers ICs applications.
- Battery Powered Instruments
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Wireless Local Loop
- Frame Relay Equipment
- Switching Systems
- Battery-powered systems
- Cable Modem
- PDH Multiplexers
- Remote Powered Equipment
- Battery Powered Systems