MAX4583ESE+T
| Parameters | |
|---|---|
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | MAX4583 |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Operating Supply Voltage | 6V |
| Number of Channels | 1 |
| Number of Circuits | 3 |
| Max Supply Voltage | 12V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 200 ns |
| Voltage - Supply, Single/Dual (±) | 2V~12V ±2V~6V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 100 ns |
| Max Dual Supply Voltage | 6V |
| On-State Resistance (Max) | 80Ohm |
| Min Dual Supply Voltage | 2V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 73 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 6pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 200ns, 100ns |
| Charge Injection | 0.5pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -73dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.02A |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 80Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 3 |
MAX4583ESE+T Overview
The electrical component comes in 16-SOIC (0.154, 3.90mm Width) packaging, which makes it convenient to ship overseas. The advanced packaging method Tape & Reel (TR) provides high reliability. A switch device like this is mounted in Surface Mount. Multiplexer and demultiplexer circuits have a number 2:1. Around -40°C~85°C TA is the extended operating temperature. 16 terminations have been made so far. The electronic part provides high-quality output because it has 1 channels. If the voltage supply is 5V volts, the electrical component should be turned on and run. There is an electrical component included in the 16 series. These analog multiplexers are built based on SPDT switching circuits. A 3 circuit is present in this switch device. Use MAX4583 to search for variants of the digital switches. Analog switches have 80Ohm internal resistance. The analogue multiplexer in this example is a typical Multiplexer or Switches. Users shouldn't supply more than 12V voltage to the switch device. The digital multiplexer has a low cost Dual, Single supply. There should be 2V voltage fed to the electrical part below 2V. This digital switch can be operated with a current of 1μA. A digital multiplexer may suffer damage if voltage is applied above 1μA. For this switch, a dual supply voltage is feasible, but it must not exceed 6VWith dual power supplies, you should attach at least 2V. The electrical part can be operated at 6V voltage levels.
MAX4583ESE+T Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
MAX4583ESE+T Applications
There are a lot of Maxim Integrated MAX4583ESE+T Analog Switches & Multiplexers ICs applications.
- PDH Multiplexers
- Cellular phones
- Automotive applications
- 65 V DACs
- Access Concentrators
- Sample-and-hold systems
- Modems
- Central office
- Channel Banks
- Medical Instrumentation
