Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
Published |
2014 |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
80Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
696mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
3 |
Supply Voltage |
5V |
Terminal Pitch |
1.27mm |
Base Part Number |
MAX4583 |
Pin Count |
16 |
JESD-30 Code |
R-PDSO-G16 |
Operating Supply Voltage |
6V |
Number of Channels |
1 |
Number of Circuits |
3 |
Max Supply Voltage |
12.6V |
Min Supply Voltage |
2V |
Operating Supply Current |
1μA |
Max Supply Current |
1μA |
Turn On Delay Time |
200 ns |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
100 ns |
On-State Resistance (Max) |
80Ohm |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
73 dB |
Current - Leakage (IS(off)) (Max) |
2nA |
Channel Capacitance (CS(off), CD(off)) |
4pF 6pF |
On-state Resistance Match-Nom |
1Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
200ns, 100ns |
Charge Injection |
0.5pC |
Channel-to-Channel Matching (ΔRon) |
1 Ω |
Crosstalk |
-96dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Voltage - Supply, Single (V+) |
2V~12V |
Height Seated (Max) |
1.75mm |
Length |
9.9mm |
Radiation Hardening |
No |
RoHS Status |
ROHS3 Compliant |
MAX4583LESE+ Overview
Shipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.154, 3.90mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tube. Multiplexers like this are mounted in the Surface Mount position. Multiplexers and demultiplexers have a ratio of 2:1. Operational temperature extended around -40°C~85°C TA. Totally, there are 16 terminations. The electronic part provides high-quality output because it has 1 channels. When the electronic component is given a voltage of 5V, it should be turned on and run. Into the electrical component body are injected 16 pins. A SPDT switching circuit is used to build these analog multiplexers. Circuits number 3 make up this analogue multiplexer. Use MAX4583 to search for variants of the digital switches. This digital multiplexer has 80Ohm internal resistance. Theswitch device is a typical Multiplexer or Switches. Users should never supply a voltage higher than 12.6V to a switch device. The analog switch ic is of the Dual, Single supply type and is cost-effective. In order for the electronic part to function properly, the lowest voltage should be 2V. 1μA current would be enough for this multiplexer to operate. This analog switch requires a voltage of 2V~12V to drain from a single voltage supply. It may damage the digital multiplexer if the voltage is higher than 1μA. The electronic component can function from 6V.
MAX4583LESE+ Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
MAX4583LESE+ Applications
There are a lot of Maxim Integrated MAX4583LESE+ Analog Switches & Multiplexers ICs applications.
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Avionics test equipment
- High speed data transmission line cards
- Intelligent PBX
- Industrial
- Wireless Local Loop
- Precision test equipment
- PDAs
- Avionics
- Sample-and-hold systems