MAX4583LESE+T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 80Ohm |
| Terminal Finish | MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 3 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Base Part Number | MAX4583 |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Operating Supply Voltage | 6V |
| Number of Channels | 1 |
| Number of Circuits | 3 |
| Max Supply Voltage | 12.6V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 200 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 100 ns |
| On-State Resistance (Max) | 80Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 73 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 6pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 200ns, 100ns |
| Charge Injection | 0.5pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -96dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2V~12V |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4583LESE+T Overview
The electronic component is convenient to ship overseas because it is packed in a 16-SOIC (0.154, 3.90mm Width). High reliability is provided by advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. There is 2:1 ratio between the number of multiplexers and demultiplexers. Around -40°C~85°C TA is the extended operating temperature. In total, 16 terminations have occurred. A 1 channel electronic part produces high-quality output. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. It is part of the design of the 16 series that this electronic component is included. Circuits based on SPDT switching are used to construct these analog switch ics. Circuits number 3 make up this analogue multiplexer. Try searching for MAX4583 variants of the analog switch ic. An switch multiplexer with 80Ohm internal resistance has a value of 80Ohm. Theswitch device is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 12.6V. Analog switch ics with Dual, Single supply type are cost-effective. The lowest voltage fed to the electronic component should be 2V. This digital switch can be operated with a current of 1μA. A voltage of 2V~12V is required for this switch device, which drains from a single voltage source. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. A voltage of 6V can be used to operate the electronic component.
MAX4583LESE+T Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
MAX4583LESE+T Applications
There are a lot of Maxim Integrated MAX4583LESE+T Analog Switches & Multiplexers ICs applications.
- E1 Multiplexer
- Isolation
- DSLAMs
- Modems
- Routers
- Frame Relay Equipment
- Microwave transmission systems
- Video switching
- PBXs
- Battery-powered systems
