MAX4583LETE+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-WQFN Exposed Pad |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2014 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 80Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 3 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX4583 |
| Pin Count | 16 |
| Operating Supply Voltage | 6V |
| Number of Channels | 1 |
| Number of Circuits | 3 |
| Max Supply Voltage | 12.6V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 200 ns |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 100 ns |
| On-State Resistance (Max) | 80Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 73 dB |
| Current - Leakage (IS(off)) (Max) | 2nA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 6pF |
| On-state Resistance Match-Nom | 1Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 200ns, 100ns |
| Charge Injection | 0.5pC |
| Channel-to-Channel Matching (ΔRon) | 1 Ω |
| Crosstalk | -96dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2V~12V |
| Height Seated (Max) | 0.8mm |
| Length | 4mm |
| Width | 4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4583LETE+ Overview
The electronic component is convenient to ship overseas because it is packed in a 16-WQFN Exposed Pad. High reliability is achieved by using advanced packaging method Tube. There is an analog multiplexer mounted in position Surface Mount. 2:1 is the ratio of multiplexer to demultiplexer circuits. Increasing operating temperature to around -40°C~85°C TA. In total, there have been 16 terminations. By its 1 channels, the electronic component provides high-quality output. When the electronic component is given a voltage of 5V, it should be turned on and run. This electronic part can be found in the 16 series. These analog multiplexers are built based on SPDT switching circuits. There are 3 circuits in this switch device. Using the MAX4583 search parameter, you can discover variants of the switch. In this multiplexer, the internal resistance is 80Ohm. Please refer to the datasheets for 16 pins functions. There is a standard Multiplexer or Switches analogue multiplexer here. Multiplexers should not be powered above 12.6V in normal situations. The digital multiplexer has a low cost Dual, Single supply. 2V is the lowest voltage that should be fed to the electronic electronic part. This digital switch can be operated with a current of 1μA. Analogue multiplexers require a 2V~12V voltage to drain from a single voltage supply. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. 6V operating voltages are supported by the electronic component.
MAX4583LETE+ Features
1 Channels
Switch Circuit: SPDT
1μA Supply Current
MAX4583LETE+ Applications
There are a lot of Maxim Integrated MAX4583LETE+ Analog Switches & Multiplexers ICs applications.
- Power routing
- Automatic test equipment
- Microprocessor controlled systems
- Industrial
- 65 V DACs
- Avionics
- Communication systems
- Data switching
- Precision data acquisition
- SDH
