MAX4583LETE+T

200ns, 100ns SPDT 80Ohm QUAD Analog Switches BREAK-BEFORE-MAKE MAX4583 16 Pins 2nA 5V 16-WQFN Exposed Pad

Manufacturer: Maxim Integrated
Nocochips NO: 503-MAX4583LETE+T
Package: 16-WQFN Exposed Pad
Datasheet: PDF
Stock: 350
Description: 200ns, 100ns SPDT 80Ohm QUAD Analog Switches BREAK-BEFORE-MAKE MAX4583 16 Pins 2nA 5V 16-WQFN Exposed Pad(Kg)

Details

Tags

Parameters
Mount	Surface Mount
Mounting Type	Surface Mount
Package / Case	16-WQFN Exposed Pad
Number of Pins	16
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
Published	2007
Pbfree Code	yes
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
ECCN Code	EAR99
Resistance	80Ohm
Subcategory	Multiplexer or Switches
Max Power Dissipation	696mW
Technology	CMOS
Terminal Position	QUAD
Number of Functions	3
Supply Voltage	5V
Terminal Pitch	0.65mm
Base Part Number	MAX4583
Pin Count	16
Operating Supply Voltage	6V
Number of Channels	1
Number of Circuits	3
Max Supply Voltage	12.6V
Min Supply Voltage	2V
Operating Supply Current	1μA
Max Supply Current	1μA
Turn On Delay Time	200 ns
Supply Type	Dual, Single
Neg Supply Voltage-Nom (Vsup)	-5V
Turn-Off Delay Time	100 ns
On-State Resistance (Max)	80Ohm
Multiplexer/Demultiplexer Circuit	2:1
Off-state Isolation-Nom	73 dB
Current - Leakage (IS(off)) (Max)	2nA
Channel Capacitance (CS(off), CD(off))	4pF 6pF
On-state Resistance Match-Nom	1Ohm
Switch Circuit	SPDT
Switch Time (Ton, Toff) (Max)	200ns, 100ns
Charge Injection	0.5pC
Channel-to-Channel Matching (ΔRon)	1 Ω
Crosstalk	-96dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Voltage - Supply, Single (V+)	2V~12V
Height Seated (Max)	0.8mm
Length	4mm
Width	4mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant

MAX4583LETE+T Overview

Packed in 16-WQFN Exposed Pad, the electronic component is convenient for shipping overseas. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. Multiplexers like this are mounted in the Surface Mount position. There is 2:1 ratio between the number of multiplexers and demultiplexers. Extended operating temperature around -40°C~85°C TA. There are 16 terminations totally. A electrical component with 1 channels is capable of high-quality output. If the voltage supply is 5V volts, the electrical component should be turned on and run. Electronic part bodies are injected with 16 pins. These analog multiplexers are built based on SPDT switching circuits. A total of 3 circuits make up this switch device. Try searching with MAX4583 to find analog multiplexer variants. There is 80Ohm internal resistance in this digital multiplexer. Datasheets for 16 pin functions are available upon request. Theswitch device is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 12.6V. An effective Dual, Single supply digital multiplexer. 2V is the lowest voltage the electrical component should receive. It would be sufficient to run this analogue multiplexer with 1μA current. An analogue multiplexer drains from a single voltage supply at 2V~12V. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. 6V operating voltages are supported by the electronic component.