MAX4590EAE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.209, 5.30mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2003 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 1.25Ohm |
| Terminal Finish | MATTE TIN |
| Max Power Dissipation | 571mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX4590 |
| Pin Count | 16 |
| Operating Supply Voltage | 20V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 5μA |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 210 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 160 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 1.25Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 53 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 115pF 115pF |
| On-state Resistance Match-Nom | 0.05Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 160ns, 210ns |
| Charge Injection | -60pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω |
| Crosstalk | -65dB @ 1MHz |
| Height Seated (Max) | 1.99mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX4590EAE+T Overview
This electronic part is conveniently packaged in 16-SSOP (0.209, 5.30mm Width), making it easy to ship abroad. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. Surface Mount is where this multiplexer is located. 1:1 is the ratio between multiplexers and demultiplexers. Operating temperature extended to -40°C~85°C TA. A total of 16 terminations have been recorded. This electronic part offers high-quality output due to its 1 channels. It is safe to turn on and run the electronic component with a 15V voltage supply. As part of its design, the 16 series is equipped with this electronic component. The analog switch ics are built using SPST - NO switching circuits. There are 2 circuits in this multiplexer. Try searching with MAX4590 if you're looking for variants. An switch multiplexer with 1.25Ohm internal resistance has a value of 1.25Ohm. The functions of 16 pins can be found in the datasheets. In a normalsituation, users should not supply the switches with voltage higher than 36V. An effective Dual, Single supply digital multiplexer. There should be 4.5V voltage fed to the electrical part below 4.5V. Putting voltage greater than 500nA on the multiplexer may cause damage. There is no problem with using dual supply voltage, but it should not exceed 20V. You should attach at least 4.5V voltage if you are using dual power supply. Operating voltages range from 20V.
MAX4590EAE+T Features
1 Channels
Switch Circuit: SPST - NO
MAX4590EAE+T Applications
There are a lot of Maxim Integrated MAX4590EAE+T Analog Switches & Multiplexers ICs applications.
- Video signal routing
- Cross Connects
- DSUs
- Industrial
- Voice over IP/DSL – Integrated Access Devices, Smart
- Remote wireless modules
- Medical systems
- Ultrasound
- 65 V DACs
- Digital cross connects (DSX-1)
