MAX4590EWE
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2003 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 1.25Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 571mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4590 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 20V |
| Power Supplies | 5/30/+-5/+-15V |
| Number of Channels | 1 |
| Number of Circuits | 2 |
| Max Supply Voltage | 36V |
| Min Supply Voltage | 4.5V |
| Nominal Supply Current | 5μA |
| Max Supply Current | 500nA |
| Throw Configuration | SPST |
| Turn On Delay Time | 210 ns |
| Voltage - Supply, Single/Dual (±) | 4.5V~36V ±4.5V~20V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 160 ns |
| Max Dual Supply Voltage | 20V |
| On-State Resistance (Max) | 1.25Ohm |
| Min Dual Supply Voltage | 4.5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 53 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 115pF 115pF |
| On-state Resistance Match-Nom | 0.05Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 160ns, 210ns |
| Charge Injection | -60pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω |
| Crosstalk | -65dB @ 1MHz |
| Normal Position | NO |
| Length | 10.3mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
MAX4590EWE Overview
Shipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.295, 7.50mm Width). To ensure high reliability, a new packaging method Tube is used. A switch device like this is mounted in Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Operating temperature around -40°C~85°C TA extended. Totally, there are 16 terminations. Due to its 1 channels, the electrical component produces high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. 16 pins are injected to the electronic part body. Multiplexers built on a SPST - NO switching circuit are built. A 2 circuit is present in this switch device. Try searching with MAX4590 to find analog multiplexer variants. It has an internal resistance of 1.25Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. In this analog multiplexer, the value is Multiplexer or Switches. Multiplexers should not be powered above 36V in normal situations. The digital multiplexer has a low cost Dual, Single supply. 4.5V is the lowest voltage the electrical component should receive. Putting voltage greater than 500nA on the multiplexer may cause damage. For this switch, a dual supply voltage is feasible, but it must not exceed 20VWith dual power supplies, you should attach at least 4.5V. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. Operating voltages of 20V are compatible with the electrical part.
MAX4590EWE Features
1 Channels
Switch Circuit: SPST - NO
MAX4590EWE Applications
There are a lot of Maxim Integrated MAX4590EWE Analog Switches & Multiplexers ICs applications.
- Signal routing between systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- DVD-R
- Relay replacements
- USB 1.1 signal switching circuits
- Cable PC
- Industrial
- CSU
- Battery Powered Instruments
- Precision instrumentation
