MAX4592ESE
| Parameters | |
|---|---|
| Voltage - Supply, Single (V+) | 3V~16V |
| Normal Position | NO |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2000 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 20Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 12V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4592 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 3V |
| Nominal Supply Current | 1nA |
| Max Supply Current | 1μA |
| Turn On Delay Time | 80 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 45 ns |
| On-State Resistance (Max) | 20Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 80ns, 45ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -85dB @ 10MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 90ns |
| Switch-off Time-Max | 50ns |
MAX4592ESE Overview
Shipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.154, 3.90mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tube. There is an analog multiplexer mounted in position Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. The operating temperature is extended to around -40°C~85°C TA. A total of 16 terminations have been recorded. A electrical component with 1 channels is capable of high-quality output. Powered by a 12V voltage supply, the electrical part should be switched on and run. An electrical component of this type can be found in the 16 series. SPST - NO switching circuits are used in these analog switch ics. It consists of 4 circuits. Look for analog switch ic variants by searching with MAX4592. Analog switches have 20Ohm internal resistance. The functions of 16 pins can be found in the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. It is generally not recommended to supply a voltage higher than 16V to the switch device in normal circumstances. An effective Single supply digital multiplexer. The lowest voltage fed to the electronic component should be 3V. This analogue multiplexer requires a voltage of 3V~16V when it drains from a single voltage supply. When the digital multiplexer is charged above 1μA, damage can occur. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. There is a voltage range of 15V operating voltages for the electrical part.
MAX4592ESE Features
1 Channels
Switch Circuit: SPST - NO
MAX4592ESE Applications
There are a lot of Maxim Integrated MAX4592ESE Analog Switches & Multiplexers ICs applications.
- SDH/SONET multiplexers
- PDH Multiplexers
- MP3 players
- Signal routing between systems
- Audio and video routing
- ISDN NT1/TA
- Fiber In The Loop (FITL)
- Digital Cross-Connects
- Cable PC
- Power routing
