MAX4593CSE
| Parameters | |
|---|---|
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Additional Feature | CAN ALSO OPERATES AT 15 V SUPPLY, OVERVOLTAGE PROTECTION |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 4 |
| Supply Voltage | 12V |
| Terminal Pitch | 1.27mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4593 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Qualification Status | Not Qualified |
| Supply Voltage-Max (Vsup) | 16V |
| Power Supplies | 12/15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| On-State Resistance (Max) | 20Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 80ns, 45ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -85dB @ 10MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 90ns |
| Switch-off Time-Max | 50ns |
| Voltage - Supply, Single (V+) | 3V~16V |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tube |
| Published | 2000 |
| JESD-609 Code | e0 |
MAX4593CSE Overview
As the electronic part is packed in 16-SOIC (0.154, 3.90mm Width), international shipping is convenient. In order to provide high reliability, an advanced packaging method Tube is used. Surface Mount is where this multiplexer is located. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. Around 0°C~70°C TA is the extended operating temperature. Total terminations are 16. A electrical component with 1 channels is capable of high-quality output. With a 12V voltage supply, the electrical component should be turned on and run. There are 16 pins injected into the electronic part body. These analog multiplexers are built based on SPST - NO/NC switching circuits. The circuits in this analogue multiplexer number 4. Try searching for the analog switch ic with MAX4593 if you are looking for variants. The analog multiplexer shown here is a typical Multiplexer or Switches. Using only a single voltage supply, this analog switch requires 3V~16V voltage. The outputs of this digital multiplexer are SEPARATE OUTPUT in number. Check out the electrical component's additional features, such as the following: CAN ALSO OPERATES AT 15 V SUPPLY, OVERVOLTAGE PROTECTION.
MAX4593CSE Features
1 Channels
Switch Circuit: SPST - NO/NC
Additional Features: CAN ALSO OPERATES AT 15 V SUPPLY, OVERVOLTAGE PROTECTION
MAX4593CSE Applications
There are a lot of Maxim Integrated MAX4593CSE Analog Switches & Multiplexers ICs applications.
- MP3 players
- Channelized and Unchannelized DS3 applications
- Private Branch Exchange (PBX)
- Automotive applications
- Automatic test equipment
- Residential Gateways, Home Gateway/Router
- Signal routing between systems
- Medical
- DSUs
- Isolation
