MAX4593CSE+T
| Parameters | |
|---|---|
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 20Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 696mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 12V |
| Terminal Pitch | 1.27mm |
| Base Part Number | MAX4593 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| JESD-30 Code | R-PDSO-G16 |
| Operating Supply Voltage | 15V |
| Number of Channels | 1 |
| Number of Circuits | 4 |
| Max Supply Voltage | 16V |
| Min Supply Voltage | 3V |
| Max Supply Current | 1μA |
| Turn On Delay Time | 80 ns |
| Turn-Off Delay Time | 45 ns |
| On-State Resistance (Max) | 20Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 72 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| On-state Resistance Match-Nom | 0.5Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 80ns, 45ns |
| Charge Injection | 2pC |
| Channel-to-Channel Matching (ΔRon) | 500m Ω |
| Crosstalk | -85dB @ 10MHz |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 3V~16V |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Operating Temperature | 0°C~70°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2000 |
| JESD-609 Code | e3 |
MAX4593CSE+T Overview
Due to its 16-SOIC (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. High reliability is achieved by using advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have a number of circuits 1:1. Operational temperature extended around 0°C~70°C TA. A total of 16 terminations have been recorded. A electrical component with 1 channels is capable of high-quality output. A 12V voltage supply should turn on and run the electronic component. There is an electrical component included in the 16 series. Unlike digital switches, these are based on SPST - NO/NC switching circuits. A total of 4 circuits make up this switch device. Look for analog switch ic variants by searching with MAX4593. As far as internal resistance is concerned, it has 20Ohm. The analog multiplexer shown here is a typical Multiplexer or Switches. Users shouldn't supply more than 16V voltage to the switch device. There should be 3V voltage fed to the electrical part below 3V. A voltage of 3V~16V is required to drain this analog switch from a single voltage supply. A voltage higher than 1μA may cause damage to the switch multiplexer. The digital multiplexer has SEPARATE OUTPUT outputs that can be used. Operating voltages of 15V are compatible with the electrical part.
MAX4593CSE+T Features
1 Channels
Switch Circuit: SPST - NO/NC
MAX4593CSE+T Applications
There are a lot of Maxim Integrated MAX4593CSE+T Analog Switches & Multiplexers ICs applications.
- Communications systems
- Mechanical reed relay replacement
- USB 1.1 signal switching circuits
- Fault Tolerant Systems
- SDH/SONET multiplexers
- Fiber In The Loop (FITL)
- Multiplexers
- Microprocessor controlled systems
- E1 Multiplexer
- Medical Instrumentation
