MAX4594DBVR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Weight | 11.198062mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Base Part Number | MAX4594 |
| Pin Count | 5 |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 45 ns |
| Supply Type | Single |
| Bandwidth | 300MHz |
| Turn-Off Delay Time | 50 ns |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 35ns, 40ns |
| Charge Injection | 2pC |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.4V~5.5V |
| Normal Position | NO |
| Height | 1.45mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Thickness | 1.2mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX4594DBVR Overview
Shipping overseas is convenient with the electronic component packed in SC-74A, SOT-753. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). It is mounted in the position Surface Mount. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operational temperature extended around -40°C~85°C TA. There are 5 terminations totally. The electronic part delivers high-quality output through its 1 channels. In the case of a voltage supply of 3V volts, the electrical part can be powered up and run. There is an electrical component included in the 5 series. A SPST - NO switching circuit is used to build these analog multiplexers. If you are looking for variants of the digital switch, trying search with MAX4594. A 10Ohm internal resistance characterizes this multiplexer. The datasheets for the 5 pins explain the functions. The analog multiplexer shown here is a typical Multiplexer or Switches. Users shouldn't supply more than 5.5V voltage to the switch device. Analogue multiplexers of the Single supply type that are cost-effective. The lowest voltage the electronic part should receive is 2V. The switch device would be able to operate with 1μA current. The voltage required by this switch device is 2.4V~5.5V, draining from a single voltage supply. When the digital multiplexer is charged above 1μA, damage can occur. 300MHz bandwidths enable data to be transferred.
MAX4594DBVR Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
Bandwidth: 300MHz
MAX4594DBVR Applications
There are a lot of Texas Instruments MAX4594DBVR Analog Switches & Multiplexers ICs applications.
- Avionics test equipment
- Audio signal routing
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Automatic test equipment
- DSUs
- PBX interfaces
- Industrial control systems
- Cross Connects
- Cable Modem
- Remote Powered Equipment
