MAX4594DCKR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Weight | 2.494758mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Base Part Number | MAX4594 |
| Pin Count | 5 |
| Power Supplies | 5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 35 ns |
| Supply Type | Single |
| Bandwidth | 300MHz |
| Turn-Off Delay Time | 40 ns |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 35ns, 40ns |
| Charge Injection | 2pC |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 2.4V~5.5V |
| Normal Position | NO |
| Height | 1.1mm |
| Length | 2mm |
| Width | 1.25mm |
| Thickness | 900μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX4594DCKR Overview
Shipping overseas is convenient with the electronic component packed in 5-TSSOP, SC-70-5, SOT-353. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have the same number of circuits 1:1. Operating temperature around -40°C~85°C TA extended. In total, 5 terminations have occurred. Due to its 1 channels, the electrical component produces high-quality output. When the electronic component is given a voltage of 3V, it should be turned on and run. There are 5 pins injected into the electronic part body. A SPST - NO switching circuit is used for these analog switches. If you are looking for variants of the digital switch, trying search with MAX4594. In this multiplexer, the internal resistance is 10Ohm. To find out what the 5 pins do, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. A voltage higher than 5.5V should not normally be supplied to the switches. Single supply type digital switch with a low cost. It is recommended to use 2V as the lowest voltage for the electrical part. The switch device would be able to operate with 1μA current. This analog switch requires a voltage of 2.4V~5.5V to drain from a single voltage supply. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. The data can be transferred over a wide range of bandwidths, called 300MHz bandwidths.
MAX4594DCKR Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
Bandwidth: 300MHz
MAX4594DCKR Applications
There are a lot of Texas Instruments MAX4594DCKR Analog Switches & Multiplexers ICs applications.
- SDH
- SONET
- Power routing
- Fiber In The Loop (FITL)
- Residential Gateways, Home Gateway/Router
- Remote wireless modules
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Communication systems
- Multi-Line E1 Interface Cards
- High reliability control systems
