MAX4594DCKRG4
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 4 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Weight | 2.494758mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Resistance | 10Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | MAX4594 |
| Pin Count | 5 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 45 ns |
| Supply Type | Single |
| Bandwidth | 300MHz |
| Turn-Off Delay Time | 50 ns |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 35ns, 40ns |
| Charge Injection | 2pC |
| Switching | MAKE-BEFORE-BREAK |
| Voltage - Supply, Single (V+) | 2.4V~5.5V |
| Normal Position | NO |
| Height | 1.1mm |
| Length | 2mm |
| Width | 1.25mm |
| Thickness | 900μm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX4594DCKRG4 Overview
Shipping overseas is convenient with the electronic component packed in 5-TSSOP, SC-70-5, SOT-353. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. In Surface Mount, you'll find this switch device. Multiplexers and demultiplexers have a number of circuits 1:1. Operating temperature extended to -40°C~85°C TA. Totally, there are 5 terminations. As a result of its 1 channels, this electronic component provides high-quality output. If the voltage supply is 3V volts, the electrical component should be turned on and run. The electrical component body receives 5 pins. Circuits based on SPST - NO switching are used to construct these analog switch ics. Try searching with MAX4594 to find analog multiplexer variants. There is 10Ohm internal resistance in this digital multiplexer. To find out what the 5 pins do, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. Users should never supply a voltage higher than 5.5V to a switch device. Single supply type digital switch with a low cost. 2V is the lowest voltage the electrical component should receive. In order to operate this switch device, it would need a current of 1μA. Using only a single voltage supply, this analog switch requires 2.4V~5.5V voltage. A voltage higher than 1μA may cause damage to the switch multiplexer. There are various bandwidths available for data transfer.
MAX4594DCKRG4 Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
Bandwidth: 300MHz
MAX4594DCKRG4 Applications
There are a lot of Texas Instruments MAX4594DCKRG4 Analog Switches & Multiplexers ICs applications.
- Modems
- Digital cross connects (DSX-1)
- Cross Connects
- E1 Network Equipment
- Microwave transmission systems
- Private Branch Exchange (PBX)
- Digital access cross connects
- Voice over IP/DSL – Integrated Access Devices, Smart
- ATM
- High reliability control systems
