MAX4595DCKR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Weight | 2.494758mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Base Part Number | MAX4595 |
| Pin Count | 5 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 45 ns |
| Supply Type | Single |
| Bandwidth | 300MHz |
| Turn-Off Delay Time | 50 ns |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 80 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 35ns, 40ns |
| Charge Injection | 2pC |
| Switching | MAKE-BEFORE-BREAK |
| Voltage - Supply, Single (V+) | 2.4V~5.5V |
| Normal Position | NO |
| Height | 1.1mm |
| Length | 2mm |
| Width | 1.25mm |
| Thickness | 900μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX4595DCKR Overview
Presented in 5-TSSOP, SC-70-5, SOT-353, this electrical component is convenient for overseas shipping. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have the same number of circuits 1:1. Around -40°C~85°C TA is the extended operating temperature. In total, there have been 5 terminations. As a result of its 1 channels, this electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 3V voltage supply. As part of its design, the 5 series is equipped with this electronic component. SPST - NC switching circuits are used in these analog switch ics. Try searching for the analog switch ic with MAX4595 if you are looking for variants. This digital multiplexer has 10Ohm internal resistance. To find out what the functions of 5 pins are, please refer to their datasheets. Multiplexer or Switches is a typical switch device. A voltage higher than 5.5V should not normally be supplied to the switches. A analog switch ic that has a cost-effective Single supply type. 2V should be the lowest voltage fed to the electronic component. 1μA current would be enough for this multiplexer to operate. This analog switch requires a voltage of 2.4V~5.5V to drain from a single voltage supply. When the digital multiplexer is charged above 1μA, damage can occur. This switch operates within the bandwidth of 300MHz.
MAX4595DCKR Features
1 Channels
Switch Circuit: SPST - NC
1μA Supply Current
Bandwidth: 300MHz
MAX4595DCKR Applications
There are a lot of Texas Instruments MAX4595DCKR Analog Switches & Multiplexers ICs applications.
- Channel Banks
- HDTV
- Fiber to the Home
- Relay Replacement
- CSU
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- ATM
- Sample hold systems
- Industrial
- High-Voltage
