MAX4596DCKR
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Weight | 2.494758mg |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Multiplexer or Switches |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Base Part Number | MAX4596 |
| Pin Count | 5 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Nominal Supply Current | 1μA |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 35 ns |
| Supply Type | Single |
| Bandwidth | 300MHz |
| Turn-Off Delay Time | 40 ns |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 83 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 35ns, 40ns |
| Charge Injection | 2pC |
| Switching | MAKE-BEFORE-BREAK |
| Voltage - Supply, Single (V+) | 2.4V~5.5V |
| Normal Position | NO |
| Height | 1.1mm |
| Length | 2mm |
| Width | 1.25mm |
| Thickness | 900μm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX4596DCKR Overview
Shipping overseas is convenient with the electronic component packed in 5-TSSOP, SC-70-5, SOT-353. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have a number of circuits 1:1. Operation at a temperature around -40°C~85°C TA. In total, 5 terminations have occurred. A electrical component with 1 channels is capable of high-quality output. When the electronic component is given a voltage of 3V, it should be turned on and run. This electronic part can be found in the 5 series. SPST - NO switching circuits are used in these analog switch ics. Try searching for the analog switch ic with MAX4596 if you are looking for variants. In this multiplexer, the internal resistance is 10Ohm. Datasheets for 5 pin functions are available upon request. There is a standard Multiplexer or Switches analogue multiplexer here. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. A analog switch ic that has a cost-effective Single supply type. The lowest voltage fed to the electronic component should be 2V. This digital switch can be operated with a current of 1μA. Draining from a single voltage supply, this analog switch requires a voltage of 2.4V~5.5V. Putting voltage greater than 1μA on the multiplexer may cause damage. It is possible to transfer data over a 300MHz-bandwidth.
MAX4596DCKR Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
Bandwidth: 300MHz
MAX4596DCKR Applications
There are a lot of Texas Instruments MAX4596DCKR Analog Switches & Multiplexers ICs applications.
- Microprocessor controlled systems
- Digital access cross connects
- Communication systems
- PBXs
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Modems
- Precision test equipment
- Data Acquisition Systems
- Frame Relay Equipment
