MAX4596EXK-T
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 5-TSSOP, SC-70-5, SOT-353 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| Resistance | 10Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 247mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | MAX4596 |
| Pin Count | 5 |
| Operating Supply Voltage | 5V |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2V |
| Operating Supply Current | 1μA |
| Max Supply Current | 1μA |
| Number of Bits | 4 |
| Throw Configuration | SPST |
| Turn On Delay Time | 45 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 50 ns |
| -3db Bandwidth | 300MHz |
| On-State Resistance (Max) | 10Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 83 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 8pF 8pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 35ns, 40ns |
| Charge Injection | 2pC |
| Switching | MAKE-BEFORE-BREAK |
| Switch-off Time-Max | 60ns |
| Voltage - Supply, Single (V+) | 2V~5.5V |
| Normal Position | NO |
| Length | 2mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MAX4596EXK-T Overview
The electronic part can be shipped overseas conveniently because it is packaged in 5-TSSOP, SC-70-5, SOT-353. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. A switch device like this is mounted in Surface Mount. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operation at a temperature around -40°C~85°C TA. The total number of terminations is 5. A electrical component with 1 channels is capable of high-quality output. When a voltage supply of 3V is used, the electronic component should be turned on and run. As part of its design, the 5 series is equipped with this electronic component. Unlike digital switches, these are based on SPST - NO switching circuits. There are 1 circuits in this switch device. Use MAX4596 to search for variants of the digital switches. A 10Ohm internal resistance characterizes this multiplexer. To find out what the functions of 5 pins are, please refer to their datasheets. Multiplexer or Switches is a typical switch device. Users should never supply a voltage higher than 5.5V to a switch device. A cost-effective Single supply type analogue multiplexer. It is recommended to use 2V as the lowest voltage for the electrical part. 1μA current would be enough for this multiplexer to operate. Analogue multiplexers require a 2V~5.5V voltage to drain from a single voltage supply. The analogue multiplexer may be damaged if voltage is greater than 1μA. 5V operating voltages can be used with this electrical part. 4-bits are supported.
MAX4596EXK-T Features
1 Channels
Switch Circuit: SPST - NO
1μA Supply Current
-3db Bandwidth: 300MHz
4-Bit
MAX4596EXK-T Applications
There are a lot of Maxim Integrated MAX4596EXK-T Analog Switches & Multiplexers ICs applications.
- Audio/video switches
- Relay Replacement
- Access Concentrators
- PBXs
- Multiplexers
- Power routing
- Optical Applications
- Intelligent PBX
- Microwave transmission systems
- Sample-and-hold systems
